Bissoy.com
Doctors Medicines MCQs Q&A

Stress in each element is ____

Stress in each element is ____ Correct Answer σ=E(Bq-αΔT)

Stress is a physical quantity that expresses the internal forces that neighboring particles of a continuous material exert on each other. After solving Finite element equations KQ=F for the displacements Q, the stress in each element can be obtained from equation. σ=E(Bq-αΔT).

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
In the generation of element geometries, if dx dy represents an area element in the real element and dεdη represents the corresponding area element in the master element, then what is the expression for Jacobian je?
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
Consider the following statements: The basic reason why shafts are made of steel and its alloys is: 1. The shaft is subjected to normal stress. 2. The shaft stress alternates with respect to time. 3. The shaft is subjected to pure compressive stress. 4. The shaft is subjected to the stress of constant intensity. Which of these statements are correct?
Consider the following statements: 1. The working stress design is based on explicit consideration of the various conditions under which the structure may cease to fulfill its intended function. 2. In the case of working stress design, the structure will directly take into consideration the various relevant modes of failure. 3. In the working stress method, regulatory bodies or classification societies usually specify the value of the allowable stress as some fraction of the mechanical properties of materials Which of the above statements is/are correct?
Consider the following statements: 1. Cross-section of a member of truss experiences uniform stress 2. Cross-section of a beam experiences minimum stress 3. Cross-section of a beam experiences linearly varying stress 4. Cross-sections of truss members experience only compressive stress Which of the above statements are correct?
Which of the following statements are correct? 1. Stress Isobar can be prepared using Boussinesq’s stress distribution theory. 2. Equivalent point load method yields accurate results. 3. Newmark’s method relates the vertical stress with the help of influence chart. 4. Westergaard’s method helps in determination of stress distribution for layered soils. Select the correct answer using the codes given below: