Bissoy.com
Doctors Medicines MCQs Q&A

The horizontal joints that extends through the entire width of the dam section and are developed at each lift height is called as ___________________

The horizontal joints that extends through the entire width of the dam section and are developed at each lift height is called as ___________________ Correct Answer longitudinal joints

The longitudinal joint is developed at each lift height and extends through the entire width of the dam section. These joints shall run through the entire length of the dam but are staggered between transverse joints.

Related Questions

Which one is incorrect? 1. Kumabaram Lift Canal-Older name - Nohar Sohwa Lift Canal. 2. Kawar sen Lift Canal-Older name - Lunaksar Lift Canal. 3. Panna Lal Lift Canal - Older name - Gajner Lift canal. 4. Veer Tejaji Lift Canal-Older name - Bagdsar.
A group of 74 students of Class XI went on picnic. The number of students who went on picnic by each section is as follows: Section A = 15 Section B = 24 Section C = 15 Section D = 20 5 students from Section A spent as much as 4 students from Section B. 12 Section B students spent as much as 9 Section C students and 6 Section C students spent as much as 8 Section D student. If every student of a particular section spent the same amount and all the students spent Rs. 23,370 altogether, find the amount spent by each student of Section D?
A concrete gravity dam having a maximum reservoir level at 200 m and the RL of the bottom of the dam 100 m. The maximum allowable compressive stress in concrete is 3000 KN/m2 and the specific gravity of concrete is 2.4. Calculate the height of the dam and check whether it is a high dam or low dam.
There are two lifts A and B in a mall and angle of elevation made by person in lift A to the person in lift B is 45°. When lift A moves 2 m upwards and lift B moves 1 m downwards, then angle of elevation changes to 30°, then find the horizontal distance between two lifts. (Take √3 = 1.7)
Which of the following statements are true with regard to energy dissipation below a dam? (i) If the upper conjugate depth of a hydraulic jump is below the tailwater, little energy will be dissipated (ii) An upturned bucket will protect the dam from scour by moving material toward the dam. (iii) A secondary dam may increase tailwater height, thereby causing a hydraulic jump to form at the toe of the main dam. (v) A slopping apron above streambed level may be used to control the hydraulic jump so that it occurs on the apron. 
Last year, there were three sections in a competitive exam. Out of them 33 students cleared the cut-off in Section A, 34 students cleared the cut-off in Section B and 32 students cleared the cut-off in Section C. 10 students cleared the cut-off in section A and section B, 9 cleared the cut-off in section B and section C and 8 cleared the cut-off in section A and section C. The number of students who cleared only one section was equal and was 21 for each section. How many students cleared all the three sections?
The average of the height of the 20 employee of the company is 1.5 m.In the month of June, two employees named Rita and Sumit left the company whose height are 1.4 m and 1.6 m respectively. In August, two more people left the company whose average of height is 1.7 m and one person join the company whose height is 87.5% of height of Sumit. Before the December, more four people left the company whose height are 1.3 m, 1.1 m, 1.32 m and 1.25 m respectively and more 5 people join the company whose height are 1.26 m, 1.18 m, 1.39 m and 1.4 m respectively. The average of height in the month of September is ….
A semicircular disc rests on a horizontal surface with its top flat surface horizontal and circular portion touching down. The coefficient of friction between semi circular disc and horizontal surface is µ. This disc is to be pulled by a horizontal force applied at one edge and it always remains horizontal. When the disc is about to start moving, its top horizontal force will
A semi-circular disc rests on a horizontal surface with its top flat surface horizontal and circular portion touching down. The coefficient of friction between semi-cricular disc and horizontal surface is i. This disc is to be pulled by a horizontal force applied at one edge and it always remains horizontal. When the disc is about to start moving, its top horizontal force will
The figure below shows a symbolic representation of the surface texture in a perpendicular lay orientation with indicative values (I through VI) marking the various specifications whose definitions are listed below. P: Maximum Waviness Height (mm); Q: Maximum Roughness Height (mm); R: Minimum Roughness Height (mm); S: Maximum Waviness Width (mm); T: Maximum Roughness Width (mm); U: Roughness Width Cutoff (mm); The correct match between the specifications and the symbols (I to VI) is