Bissoy.com
Doctors Medicines MCQs Q&A

For a transmission system of voltage ‘765 kV’ volts having the core radius of ‘5’ cm and outer radius of ‘0.40’ m. The maximum dielectric stress on single core cable is _________

For a transmission system of voltage ‘765 kV’ volts having the core radius of ‘5’ cm and outer radius of ‘0.40’ m. The maximum dielectric stress on single core cable is _________ Correct Answer 7357.7 kV

The maximum stress will occur at the surface of the conductor such that x(min) = radius of core.

Related Questions

Consider a system having a cable of capacitance 5 nF, with 765 kV star connected at 50 Hz having a power loss in the cable as 82.1 kW. Then the dielectric loss angle is _________(in degrees).
A suspension string have 3 units. Voltage across topmost and lower most unit of string are 6.71 volts and 11 volts respectively. What is the voltage across middle string, if voltage across whole string is 25.76 volts?
A single core cable is graded by using three dielectrics with relative permittivity 5,4,3 respectively. The diameter of the conductor is 2cm and the overall diameter is 8 cm. If the three dielectric work at the same maximum stress of 40kV/cm, then the safe working rms voltage of cable is ______ kV
S1: Instantly the full load yanked Gordy towards the side of the bridge.
P: But the pull of the cable was too much.
Q: He could hardly feel the cable, slipping through his fingers, ripping off his gloves, and streaking over the railing like an escaping snake.
R: It smashed his hands hard against the top of the railing, causing a split - second feeling of fierce pain followed by numbness.
S: He held on to the cable; it had been hard work lifting it, and he did not want to have to start over again.
S6: Feeling a sharp burning sensation where the cable was speeding between his things, Gordy rose on tiptoe and as he did, the slithering coil of cable tightened around his left foot and yanked him over the railing.

The Proper sequence should be:
Seven people A, B, C, D, E, F and G live on separate floors of a 7-floor building. Ground floor is numbered 1, first floor is numbered. 2 and so on until the topmost floor is numbered 7. Each one of these having a different cars-Cadillac, Ambassador, Fiat, Maruti, Mercedes, Bedford and Fargo but not necessarily in the same order. Only three people live above the floor on which A lives. Only one person lives between A and the one having a car Cadillac. F lives immediately below the one having a car Bedford. The one having a car Bedford lives on an even-numbered floor. Only three people live between the ones having a car Cadillac and Maruti. E lives immediately above C. E is not having a car Maruti. Only two people live between B and the one having a car Fargo. The one having a car Fargo lives below the floor on which B lives. The one having a car Fiat does not live immediately above D or immediately below B. D does not live immediately above or immediately below A. G does not have a car Ambassador. Question : How many people live between the floors on which D and the one having a car Bedford ?
The circuit shown below has the following parameters: V1 = 8 Volts V2 = 6 Volts Vs = 10V/√2 (rms) Voltage drop across D1 & D2 = 0.7 Volts At the load (R), the peak value in the positive half cycle will be
The circuit shown below has the following parameters: Voltage drop across D1 & D2 = 0.7 Volts V1 = 8 Volts V2 = 6 Volts Vs = 10V/√2 (RMS) At the load (R), the peak value in the negative half cycle is
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the radial stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². Calculate the tangential stress due to shrink shift in inner tube. b) -3.04 c) -3.04 d) +3.04
A high pressure cylinder consists of a steel tube with inner and outer diameters 30 and 60mm respectively. It is jacketed by an outer steel tube, having an outer diameter of 90mm. Maximum principal stress induced is 80N/mm². In service the cylinder is further subjected to an internal pressure of 25MPa. Calculate the radial stress in compound cylinder. b) +3.75 c) -3.75 d) +3.75