Bissoy.com
Doctors Medicines MCQs Q&A

Consider a square wave having a peak to peak amplitude of 275mv and it is amplified to a peak to peak amplitude of 4v, with rise time of 5.2µs. Calculate the slew rate?

Consider a square wave having a peak to peak amplitude of 275mv and it is amplified to a peak to peak amplitude of 4v, with rise time of 5.2µs. Calculate the slew rate? Correct Answer 0.615 v/µs

From the definition of rise time, the change in the output voltage is 5.2µs △v= (90%-10%)×4v= (0.9-0.1)×4v =3.2v. Therefore, slew rate = 3.2v/5.2µs =0.615v/µs.

Related Questions

Given below are three quantities named 1, 2 and 3. Based on the given information, you have to determine the relationship between the three quantities. You should use the given data and knowledge of Mathematics to choose between the possible answer. Quantity 1: Area of the innermost square. A square is made by joining the midpoints of a square of area 200 sq. m. The outermost square is called Square 1, The square inside it is called Square 2. The next square is made by joining midpoints of square 2 and is called Square 3. This process goes on. Square 5 is the innermost square. Quantity 2: A man starts with a speed of 10 km/hr. He increases his speed by 10 km/hr every hour at the start and drives at the same speed for that hour. If he traveled a total distance of 550 km. Find the time Quantity 3: Height of cylinder Its volume is equal to the volume of a cone whose radius is 14 cm and height is 39.3 cm. The radius of the cylinder is 14 cm
Consider the following statements: 1. The delay time is the time required to reach 50% of the final value in the first time. 2. The rise time is the time required for the response to rise from 10% to 90% of its final value for underdamped systems. 3. The rise time is the time required for the response to rise from 0 to 100% for the underdamped systems. Which of these statements are correct?
Seven people A, B, C, D, E, F and G live on separate floors of a 7-floor building. Ground floor is numbered 1, first floor is numbered. 2 and so on until the topmost floor is numbered 7. Each one of these having a different cars-Cadillac, Ambassador, Fiat, Maruti, Mercedes, Bedford and Fargo but not necessarily in the same order. Only three people live above the floor on which A lives. Only one person lives between A and the one having a car Cadillac. F lives immediately below the one having a car Bedford. The one having a car Bedford lives on an even-numbered floor. Only three people live between the ones having a car Cadillac and Maruti. E lives immediately above C. E is not having a car Maruti. Only two people live between B and the one having a car Fargo. The one having a car Fargo lives below the floor on which B lives. The one having a car Fiat does not live immediately above D or immediately below B. D does not live immediately above or immediately below A. G does not have a car Ambassador. Question : How many people live between the floors on which D and the one having a car Bedford ?
Which of the following statements are true/false?
1. A minimum rate of wages for the time spent by employees for the production of output is minimum time rate.
2. Minimum piece rate is the rate based on the quantity of the output employees have produced.
3. The guaranteed time rate is a minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis.
4. A minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis is overtime rate.
Consider a symmetrical square wave of 20-V peak-to-peak, 0 average, and 2-ms period applied to a Miller integrator. Find the value of the time constant CR such that the triangular waveform at the output has a 20-V peak-to-peak amplitude.
For operation with 10-V output pulses with the requirement that the sum of the rise and fall times represent only 20% of the pulse width (at half amplitude), what is the slew-rate requirement for an op amp to handle pulses 2 µs wide? (Note: The rise and fall times of a pulse signal are usually measured between the 10%- and 90%-height points.)
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If Vi = 0.5 V, what is the maximum frequency before the output distorts?
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If f = 20 kHz, what is the maximum value of Vi before the output distorts?
For an instrumentation amplifier, the following parameters are given (a) High input resistance and low power consumption (b) Low input resistance and low power consumption (c) High CMRR and high slew rate (d) Low CMRR and high slew rate Which of the given parameters are a major requirement for an instrumentation amplifier?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise -fall periods and rise and fall periods should be same. The maximum rise in follower is 30 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?