Bissoy.com
Doctors Medicines MCQs Q&A

Which of the following code is a class of non-binary BCH?

Which of the following code is a class of non-binary BCH? Correct Answer Reed Solomon codes

The most important and most common class of non binary is the family of codes known as Reed Solomon codes. BCH codes are among the most popular block codes that exist for a wide range of rates, achieve significant coding gains.

Related Questions

Which of the following command options are displayed when you use the Router# show frame-relay ? command?
1. dlci
2. neighbors
3. lmi
4. pvc
5. map
Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
1. show version
2. show protocols
3. show interfaces
4. show controllers
5. show ip interface
To enable EIGRP, which of the following would you use?
1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
2. Router1(config-if)# ipv6 router rip 1
3. Router1(config)# ipv6 router eigrp 10
4. Router1(config-rtr)# no shutdown
5. Router1(config-if)# ipv6 eigrp 10
Which two of the following commands will place network 10.2.3.0/24 into area 0?
1. router eigrp 10
2. router ospf 10
3. network 10.0.0.0
4. network 10.2.3.0 0.0.0.255 area0
5. network 10.2.3.0 0.0.0.255 area 0
Which three commands can be used to check LAN connectivity problems on a router?
1. show interfaces
2. show ip route
3. tracert
4. ping
5. dns lookups
You need to allow one host to be permitted to attach dynamically to each switch interface. Which two commands must you configure on your catalyst switch to meet this policy?
1. Switch (config-if) # ip access-group 10
2. Switch (config-if) # switchport port-security maximum 1
3. Switch (config) # access-list 10 permit ip host 1
4. Switch (config-if) # switchport port-security violation shutdown
5. Switch (config) # mac-address-table secure
There are five classes class 1, class 2, class 3, class 4 and class 5 in a school. They are one above the other. Class 1 is at the bottom, then class 2 above it and so on. Five videos M1, M2, M3, M4 and M5 are displayed in these given classes. Only one video is displayed in a particular class. Each video is displayed only one time. Video M5 is displayed at an even numbered class. Video M2 is displayed at class 1. Video M1 is displayed at the class just below M5. Video M4 is not displayed at even numbered class. Which of the following statement is not correct?
Which two classes use the Shape class correctly?
A. public class Circle implements Shape { private int radius; }B. public abstract class Circle extends Shape { private int radius; }C. public class Circle extends Shape { private int radius; public void draw(); }D. public abstract class Circle implements Shape { private int radius; public void draw(); }E. public class Circle extends Shape { private int radius; public void draw() { /* code here */ } }F. public abstract class Circle implements Shape { private int radius; public void draw() { /* code here */ } }
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
What two multicast addresses does OSPFv3 use?
1. FF02::A
2. FF02::9
3. FF02::5
4. FF02::6