Bissoy.com
Doctors Medicines MCQs Q&A

If the signal to be analyzed is an analog signal, we would pass it through an anti-aliasing filter with B as the bandwidth of the filtered signal and then the signal is sampled at a rate __________

If the signal to be analyzed is an analog signal, we would pass it through an anti-aliasing filter with B as the bandwidth of the filtered signal and then the signal is sampled at a rate __________ Correct Answer Fs ≥ 2B

The filtered signal is sampled at a rate of Fs≥ 2B, where B is the bandwidth of the filtered signal to prevent aliasing.

Related Questions

A signal m(t) with bandwidth 500 Hz is first multiplied by a signal g(t) where
$$g\left( t \right) = \sum\limits_{k = - \infty }^\infty {{{\left( { - 1} \right)}^k}\delta \left( {t - 0.5 \times {{10}^{ - 4}}k} \right)} $$
The resulting signal is then passed through an ideal low pass filter with bandwidth 1 kHz. The output of the low pass filter would be
A signal m(t) with bandwidth 500 Hz is first multiplied by a signal g(t). The resulting signal is passed through an ideal low pass filter with bandwidth 1 kHz. The output of the low pass filter would be :
Assertion (A): Nyquist rate of sampling is the theoretical minimum sampling rate at which the signal can be sampled and still be reconstructed from its samples. Reason (R): When the Nyquist rate sampling is used, only an ideal low pass filter can be used to extract signal x(t) from sampled signal xs(t). Code:
A 1 kHz sinusoidal signal is ideally sampled at 1500 samples/sec and the sampled signal is passed through an ideal low-pass filter with cutoff frequency 800 Hz. The output signal has the frequency
Consider a circuit as shown in figure The circuit is (1) Constant K low-pass filter (2) Constant K high-pass filter (3) The m-derived low-pass filter (4) The m-derived high-pass filter
If, Fhp(u, v)=F(u, v) – Flp(u, v) and Flp(u, v) = Hlp(u, v)F(u, v), where F(u, v) is the image in frequency domain with Fhp(u, v) its highpass filtered version, Flp(u, v) its lowpass filtered component and Hlp(u, v) the transfer function of a lowpass filter. Then, unsharp masking can be implemented directly in frequency domain by using a filter. Which of the following is the required filter?
The signal $$\cos \left( {10\pi t + \frac{\pi }{4}} \right)$$   is ideally sampled at a sampling frequency of 15 Hz. The sampled signal is passed through a filter with impulse response $$\left( {\frac{{\sin \left( {\pi t} \right)}}{{\pi \tau }}} \right)\cos \left( {40\pi t - \frac{\pi }{2}} \right).$$     The filter output is
A rotary drum filter with 30% submergence is used to filter concentrated aqueous slurry of calcium carbonate containing 15lb of solids per cubic foot of water. The pressure–drop is 2011Hg. If the filter cake contains 50% mixture (wet basis), calculate the filter area required to filter 10 gal/min of slurry. The filter cycle time is 5 min. The specific cake resistance depends on the pressure–drop as: α (ft/lb) = α (Δp)0.26, where α = 2.90×1010 Viscosity of the filtrate = 6.72×10-4 lb/ft-s. Density of calcium carbonate = 168.8 lb/ft3. Neglect filter medium resistance.
A signal containing only two frequency components (3 kHz and 6 kHz) is sampled at the rate of 8 kHz, and then passed through a low pass filter with a cut-off frequency of 8 kHz. The filter output
If H(s) is the transfer function of a analog low pass normalized filter and Ωu is the desired pass band edge frequency of new low pass filter, then which of the following transformation has to be performed?