Bissoy.com
Doctors Medicines MCQs Q&A

Determine the gross calorific value (GCV) of a gas, having following results after using Boy’s calorimeter: Volume of the gaseous fuel burnt = 0.093 m3, weight of the water used for cooling = 30.5 kg, Weight of the steam condensed = 31 gm, Temperature of inlet water = 26.1 0C and Temperature of outlet water = 36.5 0C?

Determine the gross calorific value (GCV) of a gas, having following results after using Boy’s calorimeter: Volume of the gaseous fuel burnt = 0.093 m3, weight of the water used for cooling = 30.5 kg, Weight of the steam condensed = 31 gm, Temperature of inlet water = 26.1 0C and Temperature of outlet water = 36.5 0C? Correct Answer 3410 Kcal/m3

By using relation GCV = w(t2 – t1)/ V, We get GCV = 3410 Kcal/m3.

Related Questions

Determine net calorific value of a volatile liquid fuel, having following results after using Boy’s calorimeter: Volume of the liquid fuel burnt = 0.152 m3, weight of the water used for cooling = 48.5 kg, Weight of the steam condensed = 91 gm, Temperature of inlet water = 35.2 0C and Temperature of outlet water = 42.6 0C?
Calculate the GCV and NCV of a fuel from the following data. Volume of the fuel burnt at STP is 0.08m2.Weight of the water used for cooling is 24kg.Temperature of inlet and outlet water is 25oC. and 30oC respectively. Weight of water obtained by steam condensation is 0.02kg.
Eight boys are sitting around a circular table and drinking milk in their own separate glasses with ID numbers 1 to 8. Boy-2 is sitting between boy-6 and boy-7, boy-1 is sitting between boy-8 and boy-5. Boy-3 is sitting to the third left of boy-7 and boy-8 is sitting to the third right of boy-4. What is the position of boy-5 with respect to boy-3 ?
Bomb calorimeter is used to determine the (where, GCV - Gross Calorific Value. NCV - Net Calorific Value.)
A two pass surface condenser is required to handle the exhaust from a turbine developing 15 MW with specific steam consumption of 5 kg/k W h. The quality of exhaust steam is 0.9, the condenser vacuum is 66 cm of mercury while the bar meter reads 76 cm of mercury. The condenser tubes are 28 mm inside diameter, 4 mm thick and water flows through tubes with a speed of 3 m/s and inlet temperature 20 degree Celsius. All the steam is condensed, the condensate is saturated water and temperature of cooling water at exit is 5 degree Celsius less than the condensate temperature. Assuming that overall coefficient of heat transfer is 4 k W/m2 degree, determine the mass of cooling water circulated
A sample of coal containing the following elements: C=90%; H=5%; ash=4%; weight of the coal burnt=0.90g; weight of the water taken=600g; water equivalent of bomb calorimeter=2000g; rise in temperature=2.48oC; fuse wire correction=10cal; cooling correction=0.02oC; acid correction=50 cal. Calculate net and GCV of coal in cal/g. Assume latent heat of steam is 580cal/g.
Determine the water equivalent of the bomb calorimeter apparatus which gave following data during experiment: Weight of benzoic acid taken = 2.12 gm, Weight of water taken in calorimeter = 2.5kg, Initial temperature= 16.970, Final temperature = 18.650, Cooling correction = 0.035 0C, fuse wire correction = 20 calories and cotton thread correction = 2.2 calories? (Calorific value of benzoic acid=6324)
A tank has an inlet pipe and an outlet pipe. If the outlet pipe is closed then the inlet pipe fills the empty tank in 8 hours. If the outlet pipe is open then the inlet pipe fills the empty tank in 10 hours. If only the outlet pipe is open then in how many hours the full tank becomes half-full?
In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?
A tank has an optional adjustable outlet pipe that can be attached to the tank at any height we want. This outlet pipe drains water from the tank at a constant rate, while the tank is being filled using another inlet pipe at a constant rate. If the outlet, pipe is attached at half the height of the tank, the tank, which is initially empty gets filled in 18 hours. If the outlet pipe is attached at height equal to two third height of the tank, the tank, which is initially empty, is filled in 16 hours. In how many hours will the tank, which is initially empty, be completely filled if the outlet pipe is not attached to the tank?