Bissoy.com
Doctors Medicines MCQs Q&A

What does the following series of commands “Router IGRP 71 network” accomplish? 10.0.0.0 router IGRP 109 network 172.68.7.0

What does the following series of commands “Router IGRP 71 network” accomplish? 10.0.0.0 router IGRP 109 network 172.68.7.0 Correct Answer It isolates networks 10.0.0.0 and 172.68.7.0

It isolates network 10.0.0.0 and 172.68.7.0 and associates autonomous systems 109 and71 with IGRP. IGRP does not disable RIP, both can be used at the same time.

Related Questions

Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
Consider a computer network using the distance vector routing algorithm in its network layer. The partial topology of the network is as shown below. The objective is to find the shortest-cost path from the router R to routers P and Q. Assume that R does not initially know the shortest routes to P and Q. Assume that R has three neighbouring routers denoted as X, Y, and Z. During one iteration, R measures its distance to its neighbours X, Y, and Z as 3, 2, and 5, respectively. Router R gets routing vectors from its neighbours that indicate that the distance to router P from routers X, Y, and Z are 7, 6, and 5, respectively. The routing vector also indicates that the distance to router Q from routers X, Y, and Z are 4, 6, and 8, respectively. Which of the following statement(s) is/are correct with respect to the new routing table of R, after updation during this iteration ? 
A group of 2m - 1 routers are interconnected in a centralized binary tree, with router at each tree node. Router I communicate with router J by sending a message to the root of the tree. The root then sends the message back down to J. Then find the mean router-router path length.
You get a call from a network administrator who tells you that he typed the following into his router:
Router (config) #router ospf 1Router (config-router) #network 10.0.0.0 255.0.0.0 area 0
He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
Which two of the following commands will place network 10.2.3.0/24 into area 0?
1. router eigrp 10
2. router ospf 10
3. network 10.0.0.0
4. network 10.2.3.0 0.0.0.255 area0
5. network 10.2.3.0 0.0.0.255 area 0
Consider the following statements about the functionality of an IP based router. I. A router does not modify the IP packets during forwarding. II. It is not necessary for a router to implement any routing protocol. III. A router should reassemble IP fragments if the MTU of the outgoing link is larger than the size of the incoming IP packet. Which of the above statements is/are TRUE?
An OSPF router receives an LSA, the router checks its sequence number, and this number matches the sequence number of the LSA that the receiving router already has. What does the receiving router do with the LSA?
You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful?
1. TFTP server software must be running on the router.
2. TFTP server software must be running on your laptop.
3. The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable.
4. The laptop must be on the same subnet as the router's Ethernet interface.
5. The copy flash tftp command must be supplied the IP address of the laptop.