Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

The Transfer characteristic of the different types of MOSFETs is shown below, where ID is drain current and VGS is the Gate-Source voltage, the correct combination of MOSFET w.r.t to transfer characteristics is: Types of MOSFET (P) P – Channel Enhancement MOSFET (Q) P – Channel Depletion MOSFET (R) N – Channel Enhancement MOSFET (S) N – Channel Depletion MOSFET
You need to allow one host to be permitted to attach dynamically to each switch interface. Which two commands must you configure on your catalyst switch to meet this policy?
1. Switch (config-if) # ip access-group 10
2. Switch (config-if) # switchport port-security maximum 1
3. Switch (config) # access-list 10 permit ip host 1
4. Switch (config-if) # switchport port-security violation shutdown
5. Switch (config) # mac-address-table secure
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If the maximum number of valves that can be closed at the same time are closed which of the following must true?
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If R is closed and U is open, which of the following must be true?
Choose the correct statement(s) i) The gate circuit impedance of MOSFET is higher than that of a BJT ii) The gate circuit impedance of MOSFET is lower than that of a BJT iii) The MOSFET has higher switching losses than that of a BJT iv) The MOSFET has lower switching losses than that of a BJT
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. If Z is open, which of the following must be true?
The mixing vat in a factory receives liquid ingredients through six separate value--- labeled R.S.T.U,Y and Z -- each of which has exactly two settings: open and closed.The mixing vat operator must ensure that each valve is set open or closed according to the following conditions: If T is open, both S and Z must be closed, R and Z cannot both be closed at the same time; If Y is closed, Z must also be closed;S and U cannot both be open at the same time. Which of the following, if given to the mixing vat operator as an instruction, would not determine the setting of any other valve ?
A diode circuit is so arranged that when the switch is open it’s KVL gives Ri+ 1/C ∫i dt = 0 When the switch is closed, Ri+ 1/C ∫i dt = Vs Vs is the dc supply voltage. The diode is so connected that it is forward biased when switch is closed The circuit is mostly likely be a
A circuit is so formed such that the source-R-C-diode-switch are in series. Consider the initial voltage across the C to be zero. The diode is so connected that it is forward biased when the switch is closed. When the switch is closed,
A circuit is so formed such that source-R-L-diode-switch are all in series. Consider the initial current in L to be zero. The diode is so connected that it is forward biased when switch is closed. When the switch is closed,