Bissoy.com
Doctors Medicines MCQs Q&A

An NMOS amplifier is to be designed to provide a 0.50-V peak output signal across a 50-kΩ load that can be used as a drain resistor. If a gain of at least 5 V/V is needed, what value of gm is required?

An NMOS amplifier is to be designed to provide a 0.50-V peak output signal across a 50-kΩ load that can be used as a drain resistor. If a gain of at least 5 V/V is needed, what value of gm is required? Correct Answer 0.1 mA/V

gmRd = 5 or gm= 5/50 mA/V.

Related Questions

An NMOS amplifier is to be designed to provide a 0.50-V peak output signal across a 50-kΩ load that can be used as a drain resistor. What W/L ratio is required if μnCox = 200 μA/V2?
An NMOS amplifier is to be designed to provide a 0.50-V peak output signal across a 50-kΩ load that can be used as a drain resistor. Using a dc supply of 3 V, what values of ID and VOV would you choose?
Various measurements are made on an NMOS amplifier for which the drain resistor RD is 20 kΩ. First, DC measurements show the voltage across the drain resistor, VRD, to be 2 V and the gate-to-source bias voltage to be 1.2 V. Then, ac measurements with small signals show the voltage gain to be −10 V/V. What is the value of Vt for this transistor?
Various measurements are made on an NMOS amplifier for which the drain resistor RD is 20 kΩ. First, DC measurements show the voltage across the drain resistor, VRD, to be 2 V and the gate-to-source bias voltage to be 1.2 V. Then, ac measurements with small signals show the voltage gain to be −10 V/V. If the process transconductance parameter is 50μA/V2, what is the MOSFET’s W/L?
The parallel combination of a 6.8 kΩ resistor and a 10 kΩ resistor is in series with the parallel combination of a 2.2 kΩ resistor and a 1 kΩ resistor. A 100 V source is connected across the circuit. The resistor(s) with the greatest voltage drop is (are)
An amplifier operating from ±3V provide a 2.2V peak sine wave across a 100 ohm load when provided with a 0.2V peak sine wave as an input from which 1.0mA current is drawn. The average current in each supply is measured to be 20mA. What is the amplifier efficiency?
Two resistors are in series: a 5.6 kΩ resistor and a 4.7 kΩ resistor. The voltage drop across the 5.6 kΩ resistor is 10 V. The voltage across the 4.7 kΩ resistor is
An amplifier is measured to have an internal resistance of 10 kΩ, voltage gain of 100V/V and output resistance of 100 Ω. Also, when a load resistance of 1 kΩ is connected between the output resistance if found to decrease to 8 kΩ. If the amplifier is fed with the signal source having an internal resistance of 2 kΩ. Find Gm.
An amplifier is measured to have an internal resistance of 10 kΩ, voltage gain of 100V/V and output resistance of 100 Ω. Also, when a load resistance of 1 kΩ is connected between the output resistance if found to decrease to 8 kΩ. If the amplifier is fed with the signal source having an internal resistance of 2 kΩ. Find Av.
An amplifier is measured to have an internal resistance of 10 kΩ, voltage gain of 100V/V and output resistance of 100 Ω. Also, when a load resistance of 1 kΩ is connected between the output resistance if found to decrease to 8 kΩ. If the amplifier is fed with the signal source having an internal resistance of 2 kΩ. Find Gvo.