Bissoy.com
Doctors Medicines MCQs Q&A

A particular op amp using ±15-V supplies operates linearly for outputs in the range −12 V to +12 V. If used in an inverting amplifier configuration of gain –100, what is the rms value of the largest possible sine wave that can be applied at the input without output clipping?

A particular op amp using ±15-V supplies operates linearly for outputs in the range −12 V to +12 V. If used in an inverting amplifier configuration of gain –100, what is the rms value of the largest possible sine wave that can be applied at the input without output clipping? Correct Answer 84.85 mV

Peak value of input wave = 12/100 or 120 mV. Hence the rms value is 120/√2 or 84.85 mV.

Related Questions

Consider the 5 × 5 matrix \[{\text{A}} = \left[ {\begin{array}{*{20}{c}} 1&2&3&4&5 \\ 5&1&2&3&4 \\ 4&5&1&2&3 \\ 3&4&5&1&2 \\ 2&3&4&5&1 \end{array}} \right
Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. What is (approximately) the peak sine-wave input signal that can be applied without output clipping?
Select from the alternatives that combination of numbers, which will form a meaningful word if given letters are arranged accordingly. \(\begin{matrix} \ \ \ \text{A} & \rm R & \rm W & \rm L & \rm E & \rm K \\\ \downarrow & \downarrow & \downarrow & \downarrow & \downarrow & \downarrow \\\ \ \ 1 & 2 & 3 & 4 & 5 & 6 \end{matrix}\)
The inverting input terminal of an operational amplifier (op-amp) is shorted with the output terminal apart from being grounded. A voltage signal V1 is applied to the non-inverting input terminal of the op-amp. Under this configuration, the op-amp function is as
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If f = 20 kHz, what is the maximum value of Vi before the output distorts?
Determine the maximum input signal to be applied to an op-amp to get distortion free output. If the op-amp used is an inverting amplifier with a gain of 50 and maximum output amplitude obtained is 4.2V sine wave?
In designing with op amps one has to check the limitations on the voltage and frequency ranges of operation of the closed-loop amplifier, imposed by the op-amp finite bandwidth (ft), slew rate (SR), and output saturation (Vo max). Consider the use of an op amp with ftt = 2 MHz, SR = 1 V/µs, and V0 max = 10 V in the design of a non-inverting amplifier with a nominal gain of 10. Assume a sine-wave input with peak amplitude Vi. If Vi = 0.5 V, what is the maximum frequency before the output distorts?
Let A be an m × n matrix and Ban n × m matrix. It is given that determinant ($$I$$m + AB) = determinant ($$I$$n + BA), where $$I$$k is the k × k identity matrix. Using the above property, the determinant of the matrix given below is
\[\left[ {\begin{array}{*{20}{c}} 2&1&1&1 \\ 1&2&1&1 \\ 1&1&2&1 \\ 1&1&1&2 \end{array}} \right
Eigen values of the matrix \[\left[ {\begin{array}{*{20}{c}} 0&1&0&0 \\ 1&0&0&0 \\ 0&0&0&{ - 2i} \\ 0&0&{2i}&0 \end{array}} \right
In a coded language “ADETP” is coded as “$&$&&” and “DTPQUV” is coded as “&&&&$&”? What is the code word for “&&$$&$”?