Bissoy.com
Doctors Medicines MCQs Q&A

A cross-flow type air heater has an area of 50 cm2. The overall heat transfer coefficient is 100 W/m2 K and the heat capacity of both hot and cold streams is 1000 W/m K. The value of NTU is

A cross-flow type air heater has an area of 50 cm2. The overall heat transfer coefficient is 100 W/m2 K and the heat capacity of both hot and cold streams is 1000 W/m K. The value of NTU is Correct Answer 5

NTU = A U/C MIN = 5.

Related Questions

A cross flow type air heater has an area of 50 cm2. The overall heat transfer coefficient is 100 W/m2 K and heat capacity of both hot and cold stream is 1000 W/m K. The value of NTU is
Which of the following statements are true regarding cold and hot deserts: (a) Hot deserts have high temperature while cold deserts have low temperature. (b) hot deserts are battered by sun and are sandy. Cold deserts have ice and snow covered ground. (c) Hot deserts are red or orange while cold deserts are gray. (d) Hot and cold deserts experience a significant seasonal effect.
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Water (specific heat = 4 k J/kg K) enters a cross flow exchanger (both fluids unmixed) at 15 degree Celsius and flows at the rate of 7.5 kg/s. It cools air (C P = 1 k J/kg K) flowing at the rate of 10 kg/s from an inlet temperature of 120 degree Celsius. For an overall heat transfer coefficient of 780 k J/m2 hr degree and the surface area is 240 m2, determine the NTU
A polarized light of Intensity 40 Wm2 is incident on the analyzer at a certain angle. If the transmitted beam has an Intensity of 20 Wm2, the angle made with the vertical is _____________
A polarized light of Intensity 35 Wm2 is incident on the analyzer at a certain angle. If the transmitted beam has an Intensity of 30 Wm2, the angle made with the vertical is __________
The heat loss from unpainted aluminum side of a house has been calculated on the presumption that overall coefficient of heat transfer is 5 W/m 2 K. Later, it was discovered that the air pollution levels are such that fouling factor on this side is of the order of 0.0005 m2 K/W. Find overall heat transfer coefficient of dirty side
Forced air flows over a convection heat exchanger in a room heater, resulting in a convective heat transfer coefficient 1.136 k W/m2 K. The surface temperature of heat exchanger may be considered constant at 65 degree Celsius, and the air is at 20 degree Celsius. Determine the heat exchanger surface area required for 8.8 k W of heating