For a twin cylinder V-engine, the crank positions for primary reverse cranks and secondary direct cranks are shown in the below figure. The engine is a?

30° V-engine
60° V-engine
120° V-engine
150° V-engine

LohaHridoy

8 views

2025-01-04 04:42

1 Answers

AhmedNazir

Answer: Option 1

8 views Answered 2022-09-01 13:21

Related Questions

When the primary direct crank of a reciprocating engine makes an angle of $$\theta $$ with the line of stroke, then the secondary direct crank will make an angle of _________ with the line of stroke.?

1 Answers 7 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle $$\theta $$ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, the acceleration of the piston is _________ when the crank OC and connecting rod PC are at right angles to each other.?

1 Answers 5 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle θ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO. The acceleration of the piston P with respect to the crank-pin C is given by?

1 Answers 4 Views

The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)?

1 Answers 5 Views

The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)?

1 Answers 6 Views

The velocity of piston in a reciprocating steam engine is given by (where $$\omega $$ = Angular velocity of crank, r = Radius of crank pin circle, $$\theta $$ = Angle turned by crank from inner dead center and n = Ratio of length of connecting rod to the radius of crank)?

1 Answers 7 Views

The tractive force in a locomotive with two cylinders is given by (where c = Fraction of reciprocating parts per cylinder, m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank and $$\theta $$ = Angle of inclination of crank to the line of stroke)?

1 Answers 6 Views

If p₁, is the pressure of air entering the L.P. cylinder and p₂ is the pressure of air leaving the L.P. cylinder (or inter-cooler pressure), then the ratio of cylinder diameters for a single acting, two stage reciprocating air compressor with complete intercooling is given by (where D₁ = Dia. of L.P. cylinder, and D₂ = Dia. of H.P. cylinder)?

1 Answers 6 Views

In a compound steam engine, the first stage of expansion is carried out in a high pressure cylinder whereas the last expansion is completed in low pressure cylinder. The diameter of high pressure cylinder is _________ the low pressure cylinder.?

1 Answers 4 Views

There are six teachers. Out of them two are primary teachers and two are secondary teachers. They are to stand in a row, so as the primary teachers, middle teachers and secondary teachers are always in a set . The number of ways in which they can do so, is-?

1 Answers 4 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)