Bissoy.com
Doctors Medicines MCQs Q&A

Maximum shear stress theory was postulated by

Maximum shear stress theory was postulated by Correct Answer Tresca

Explanation:

Maximum Shear Stress Theory: 

  • Applied satisfactorily to ductile materials.
  • This theory states that the failure can be assumed to occur when the maximum shear stress in the complex stress system is equal to the value of maximum shear stress in simple tension.
  • The relation between the theories of failure, their suitable materials, and graphical representation is given below.

Theory

Suitable Material

Graphical Representation

Maximum Normal Stress Theory

Or

Maximum Principal Stress Theory

Or

Rankine’s Theory

Brittle material

[ alt="F1 Ashik Madhu 21.08.20 D3" src="//storage.googleapis.com/tb-img/production/20/08/F1_Ashik_Madhu_21.08.20_D3.png" style="width: 267px; height: 247px;">

Maximum Normal Strain Theory

Or

Maximum Principal Strain Theory

Or

St.Venant’s Theory

Ductile and brittle material but results are not accurate in both

[ alt="F1 Ashik Madhu 21.08.20 D4" src="//storage.googleapis.com/tb-img/production/20/08/F1_Ashik_Madhu_21.08.20_D4.png" style="width: 250px; height: 296px;">

Maximum Shear Stress Theory 

Or

   Guest & Tresca’s Theory

Ductile material

[ alt="F1 Ashik Madhu 21.08.20 D5" src="//storage.googleapis.com/tb-img/production/20/08/F1_Ashik_Madhu_21.08.20_D5.png" style="width: 203px; height: 189px;">

Maximum Strain Energy Theory

Or

Haigh and Beltrami Theory

Ductile material

[ alt="F1 Ashik Madhu 21.08.20 D6" src="//storage.googleapis.com/tb-img/production/20/08/F1_Ashik_Madhu_21.08.20_D6.png" style="width: 298px; height: 277px;">

Maximum Shear Strain Energy Theory

Or

Distortion Energy Theory

Or

Von Mises Henky Theory

Ductile material

[ alt="F1 Ashik Madhu 21.08.20 D6" src="//storage.googleapis.com/tb-img/production/20/08/F1_Ashik_Madhu_21.08.20_D6.png" style="width: 298px; height: 277px;">

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Which of the following factors are affecting critical shear stresses? 1. Purity of metals reduces the critical shear stress 2. Surface films greatly enhance the critical shear stress 3. Rise in temperature 4. Rate of deformation and the extent of initial deformation also help in raising the critical shear stress
A shaft is subjected to a maximum bending stress of 80 N/mm2 and maximum shearing stress equal to 30 N/mm2 at a particular section. If the yield point in tension of the material is 280 N/mm2 and the maximum shear stress theory of failure is used, then the factor of safety obtained will be
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
The Rheological behaviour of concrete, when represented by shear stress vs rate of shear, is characterized as Where : τ shear stress, Τ0 = (initial) yield value, μ = at-point plastic viscosity, γ̇ = at point rate of shear.
If nominal shear stress $${\tau _{\text{v}}}$$ exceeds the design shear strength of concrete $${\tau _{\text{c}}}$$, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
Shear stress versus shear rate behavior of four different types of fluids (I, II, III and IV) are shown in the figure below.
Basic Principles of Biotechnology mcq question image
Which one of the following options is correct?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
Below are given two sets in which Set I gives the named theory of Intelligence which set II indicated their main proponents and contentions associated with the theory. Match the two sets. Set I (Theory of Intelligence) Set II (The main proponents and contentions) (a) Multiple Factor Theory (i) Sternberg, intelligence can be taught and the classroom is the logical place to teach it. (b) Theory of Multiple Intelligence (ii) Cattell, intelligence is neither completely monarchic, nor oligarchic nor anarchic. (c) Theory of Fluid and Crystallized Intelligence (iii) Thurstone, intelligence is oligarchic in nature. (d) Coping Theory of Intelligence (iv) Gardner, intelligence is a capacity with component processes and should not be confused with a learning or cognitive style.   Choose correct answer from following.