Bissoy.com
Doctors Medicines MCQs Q&A

The operation of finishing a drilled hole to its right size is known as?

The operation of finishing a drilled hole to its right size is known as? Correct Answer Reaming

Concept:

Drilling: Operation of making a circular hole by removing a volume of metal from the job by a rotating cutting tool called drill

Boring: Process of enlarging a hole.

Reaming: Operation of finishing a drilled hole.

Counterboring: Operation of boring a second hole, larger in diameter than the first, but concentric with it.

Related Questions

Circular areas of same size have been marked to drill holes in a road. If the radius of one of the holes to be drilled is 21cm, and there are 10 holes to be drilled along the road, what is the total area in sq.cm of all the 10 circles marked to be drilled? (π = 22 / 7)
Operation of finishing previously drilled hole in order to bring it to accurate size and have good surface finish is known as
If a + b + c + d = 4, then find the value of $$\frac{1}{{\left( {1 - a} \right)\left( {1 - b} \right)\left( {1 - c} \right)}}$$     + $$\frac{1}{{\left( {1 - b} \right)\left( {1 - c} \right)\left( {1 - d} \right)}}$$     + $$\frac{1}{{\left( {1 - c} \right)\left( {1 - d} \right)\left( {1 - a} \right)}}$$     + $$\frac{1}{{\left( {1 - d} \right)\left( {1 - a} \right)\left( {1 - b} \right)}}$$     is?
If a + b + c + d = 4, then the value of $$\frac{1}{{\left( {1 - a} \right)\left( {1 - b} \right)\left( {1 - c} \right)}}$$     + $$\frac{1}{{\left( {1 - b} \right)\left( {1 - c} \right)\left( {1 - d} \right)}}$$     + $$\frac{1}{{\left( {1 - c} \right)\left( {1 - d} \right)\left( {1 - a} \right)}}$$     + $$\frac{1}{{\left( {1 - d} \right)\left( {1 - a} \right)\left( {1 - b} \right)}}$$     is?
In seive plate column, holes are drilled or punched in sizes ranging from 2.5 to 12 mm (5 mm being widely used). The hole pitch is normally __________ times the hole diameter to give the required hole area.
Consider the following statements regarding limits and fits 1. Actual size is the standard size for the part and is the same both for the hole and its shaft. 2: Basic size is the dimension as measured on the manufactured part. 3. Deviation is the algebraic difference between a size and the corresponding basic size. Which of the above statements is/are correct ? 
For manufacturing of a certain amount of hole, maximum hole size was found to be 50.14 mm and minimum hole size was found to be 49.98. What will be the Tolerance in mm?
For manufacturing of a certain amount of hole, maximum hole size was found to be 50.14 mm and minimum hole size was found to be 49.98. Tolerance in mm will be
Pipe A along with a hole can fill a tank in 20 minutes, pipe B along with hole can fill that tank in 1 hour. If both the pipes along with hole can fill that tank in (60/7) minutes, then what is the time taken by hole alone to empty that tank completely?
In this question, a passage and a related statement have been given. Read the passage carefully and assess the statement based on it. Using knives and screws, two Russian astronauts on Tuesday took a sample of substance around a mysterious cavity of the spacecraft called the Soyuz, which was placed in the International Space Station, a Moscow official suggested that it was a break - It can also be done. In August, two months after the last visit of the vehicle, the air leak was detected in the Soyuz spacecraft due to the 2 mm air in the ISS. Roskosmos, an astronomical institute, says that cutting off the insulation on the hole and sampling the material around it and the purpose of putting a new insulation on it is to find out that this small but dangerous hole has been done on earth or Is in space. The chief of Roskosmos has said that the error of manufacturing has not been found in the investigation. Experienced astronauts had to struggle but they managed their mission. Before the spacewalk, astronauts were able to inspect the hole just from within the spacecraft. The biggest difficulty was that in the Soyuz spacecraft, the ISS was not designed to improve during adverse weather space, and no railing was also made to catch the space passengers outside the vehicle. Statement: The mysterious hole in the So yuz spacecraft was due to the error of manufacturing. Select the appropriate from the given options A - Statement is completely true B - The statement is possibly true C - the statement can not be determined D - Statement is completely false