Bissoy.com
Doctors Medicines MCQs Q&A

lubricating oil pump circulates oil to lubricate the engine parts. The purpose of an oil hole in the connecting rod is to

lubricating oil pump circulates oil to lubricate the engine parts. The purpose of an oil hole in the connecting rod is to Correct Answer Lubricate piston pin bearing

  • In engines, a hole is drilled in the connecting rod from the big end to the small end
  • It allows oil to flow from the big end to the small end bush
  • This oil lubricates the gudgeon pin bush and piston bearings
  • The piston pin/gudgeon pin connects the piston with the connecting rod

Related Questions

Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
For a steam engine, the following data is given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m calculate inertia force at θ=30 degrees from IDC.
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.
From the data given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the correcting couple in N-m?
A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s2, then find the correction couple in N-m.
In by pass type filter arrangement, only a small portion of the lubricating oil is passed through the filter and the remaining lubricating oil is directly supplied to the bearings by the oil pump at pre-set pressure.
A small connecting rod of mass 1.5 kg is suspended in a horizontal plane by two wires 1.25 m long. The wires are attached to the rod at points 120 mm on either side of the centre of gravity. If the rod makes 20 oscillations in 40 seconds, find the radius of gyration of the rod about a vertical axis through the centre of gravity.
A small connecting rod of mass 1.5 kg is suspended in a horizontal plane by two wires 1.25 m long. The wires are attached to the rod at points 120 mm on either side of the centre of gravity. If the rod makes 20 oscillations in 40 seconds, find the mass moment of inertia of the rod about a vertical axis through the centre of gravity.
একটি পানিপূর্ণ কুয়ার গভীরতা 20m ও ব্যাস 2 m. কুয়াটিকে পানি শূণ্য করার জন্য 5 HP এর একটি পাম্প লাগানো হল। অর্ধেক পানি তোলার পর পাম্পটি নষ্ট হয়ে গেল। বাকি পানি তোলার জন্য একই ক্ষমতা সম্পন্ন আর একটি পাম্প লাগানো হল। প্রথম পাম্প দ্বারা সম্পাদিত কাজের পরিমান নির্ণয় কর।(The depth and diameter of a water filled well are 20 m and 2 m respectively. An engine of 5 HP is attached to pump out the water. The pump was ruined after emptying half of the water. Then another pump of same capacity was attached to pump out rest of the water. Determine the work done by first pump.)