Related Questions

Vapour actuated pressure spring thermometer does not require ambient temperature compensation. Ambient temperature compensation is provided in gas or liquid expansion pressure spring thermometer by
A Making the volume of thermometer bulb as large as conveniently possible
B Reducing the volume of the capillary to a minimum
C Reducing the volume of the receiving element to a minimum
D All of the above
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
A 0
B 100
C 50
D None of these
When a closely-coiled helical spring of mean diameter (D) is subjected to an axial load (W), the deflection of the spring ($$\delta $$) is given by (where d = Diameter of spring wire, n = No. of turns of the spring and C = Modulus of rigidity for the spring material)
A $$\frac{{{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
B $$\frac{{2{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
C $$\frac{{4{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
D $$\frac{{8{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be
A $$\frac{\tau }{2}$$
B $$\tau $$
C $$2\tau $$
D $$4\tau $$
Two closely coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is half that of spring 'B'. The ratio of deflections in spring 'A' to spring 'B' is
A $$\frac{1}{8}$$
B $$\frac{1}{4}$$
C $$\frac{1}{2}$$
D 2
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A $$\frac{{{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
B $$\frac{{2{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
C $$\frac{{4{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
D $$\frac{{8{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
Two closely-coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is double that of spring 'B'. The stiffness of spring 'A' will be __________ that of spring 'B'.
A One-sixteenth
B One-eighth
C One-fourth
D One-half
Two closely coiled helical springs 'A' and 'B' are equal in all respects but the diameter of wire of spring 'A' is double that of spring 'B' The stiffness of spring 'B' will be __________ that of spring 'A'
A One-sixteenth
B One-eighth
C One-fourth
D One-half
Two closely-coiled helical springs 'A' and 'B' of the same material, same number of turns and made from same wire are subjected to an axial load W. The mean diameter of spring 'A' is double the mean diameter of spring 'B'. The ratio of deflections in spring 'B' to spring 'A' will be
A $$\frac{1}{8}$$
B $$\frac{1}{4}$$
C 2
D 4
In a compound steam engine, the first stage of expansion is carried out in a high pressure cylinder whereas the last expansion is completed in low pressure cylinder. The diameter of high pressure cylinder is _________ the low pressure cylinder.
A Equal to
B Less than
C More than
D None of these

Next steps