Bissoy.com
Doctors Medicines MCQs Q&A

A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be

A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be Correct Answer $$\tau $$

Related Questions

When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
Last year, there were three sections in a competitive exam. Out of them 33 students cleared the cut-off in Section A, 34 students cleared the cut-off in Section B and 32 students cleared the cut-off in Section C. 10 students cleared the cut-off in section A and section B, 9 cleared the cut-off in section B and section C and 8 cleared the cut-off in section A and section C. The number of students who cleared only one section was equal and was 21 for each section. How many students cleared all the three sections?
Two closely-coiled helical springs 'A' and 'B' of the same material, same number of turns and made from same wire are subjected to an axial load W. The mean diameter of spring 'A' is double the mean diameter of spring 'B'. The ratio of deflections in spring 'B' to spring 'A' will be
When a closely-coiled helical spring of mean diameter (D) is subjected to an axial load (W), the deflection of the spring ($$\delta $$) is given by (where d = Diameter of spring wire, n = No. of turns of the spring and C = Modulus of rigidity for the spring material)
Consider the following statements: In case of helical gears, teeth are cut at an angle to the axis of rotation of the gears. 1) Helix angle introduces another ratio called axial contact ratio. 2) Transverse contact ratio is equal to axial contact ratio in helical gears. 3) Large transverse contact ratio does not allow multiple teeth to share the load. 4) Large axial contact ratio will cause larger axial force component Which of the above statements are correct?
If nominal shear stress $${\tau _{\text{v}}}$$ exceeds the design shear strength of concrete $${\tau _{\text{c}}}$$, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
Two closely coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is half that of spring 'B'. The ratio of deflections in spring 'A' to spring 'B' is
An open coiled helical compression spring 'A' of mean diameter 50 mm is subjected to an axial load ‘W’. Another spring 'B' of mean diameter 25 mm is similar to spring 'A' in all respects. The deflection of spring 'B' will be __________ as compared to spring 'A'.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Two closely-coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is double that of spring 'B'. The stiffness of spring 'A' will be __________ that of spring 'B'.