Joule-Thomson co-efficient is the ratio of

A Pressure change to temperature change occuring during adiabatic compression of a gas
B Pressure change to temperature change occuring during adiabatic throttling of a gas
C Temperature change to pressure change occuring during adiabatic compression of a gas
D Temperature change to pressure change occuring during adiabatic throttling of a gas

Correct Answer: Temperature change to pressure change occuring during adiabatic throttling of a gas

Bissoy MCQ
#Chemical Engineering #Chemical Engineering Basics

Related Questions

The scales form in heat exchanges after a period of operation and provide additional resistance to heat transfer with some heat transfer coefficient . The reciprocal of this scale heat transfer coefficient is called .
A scaling factor
B forming factor
C resisting factor
D fouling factor
For a shoe brake, the equivalent coefficient of friction is equal to (where $$\mu $$ = Actual coefficient of friction and $$\theta $$ = Semi-block angle)
A $$\frac{{2\mu \sin \theta }}{{\theta + \sin \theta }}$$
B $$\frac{{\mu \sin \theta }}{{2\theta + \sin 2\theta }}$$
C $$\frac{{4\mu \sin \theta }}{{\theta + \sin \theta }}$$
D $$\frac{{4\mu \sin \theta }}{{2\theta + \sin 2\theta }}$$
The value of coefficient of discharge is __________ the value of coefficient of velocity.
A Less than
B Same as
C More than
D None of these
Film coefficient is defined as the ratio of
A Thermal conductivity to the equivalent thickness of the film of fluid
B Temperature drop through the films of fluids to the thickness of film of fluids
C Thickness of film of fluid to the thermal conductivity
D Thickness of film of fluid to the temperature drop through the films of fluids
The coefficient of performance is the ratio of the refrigerant effect to the
A Heat of compression
B Work done by compressor
C Enthalpy increase in compressor
D All of the above
If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is:
A (1 - C) mf - eE
B (C - 1) mf + eE
C (C - 1) mf - eE
D (1 - C) mf + eE
‘μ’ is coefficient of friction. A wheeled vehicle travelling on a circular level track will slip and overturn simultaneously if the ratio of its wheel distance to the height of its centroid, is
A μ
B 2μ
C 3μ
D $$\frac{1}{2}$$μ
In a band and block brake, the ratio of tensions on tight side and slack side of the band is (where $$\mu $$ = Coefficient of friction between the blocks and the drum, $$\theta $$ = Semi-angle of each block subtending at the center of drum and n = Number of blocks)
A $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = \mu \theta {\text{n}}$$
B $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 - \mu \tan \theta }}{{1 + \mu \tan \theta }}} \right)^{\text{n}}}$$
C $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\mu \theta } \right)^{\text{n}}}$$
D $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 + \mu \tan \theta }}{{1 - \mu \tan \theta }}} \right)^{\text{n}}}$$
In a band and block brake, the ratio of tensions on the tight and slack sides of band is given by (where $$\mu $$ = Coefficient of friction between the blocks and the drum, $$\theta $$ = Semi-angle of each block subtending at the centre of drum and n = Number of blocks)
A $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_{\text{2}}}}} = \mu \theta \times {\text{n}}$$
B $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\mu \theta } \right)^{\text{n}}}$$
C $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 - \mu \tan \theta }}{{1 + \mu \tan \theta }}} \right)^{\text{n}}}$$
D $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 + \mu \tan \theta }}{{1 - \mu \tan \theta }}} \right)^{\text{n}}}$$
Coefficient of velocity is defined as the ratio of
A Actual velocity of jet at vena contracta to the theoretical velocity
B Area of jet at vena contracta to the area of orifice
C Actual discharge through an orifice to the theoretical discharge
D None of the above

Next steps