Bissoy.com
Doctors Medicines MCQs Q&A

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2, the Safe load on the column, should not exceed

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2, the Safe load on the column, should not exceed Correct Answer 41,200 kg

Related Questions

A short column 20cm × 20cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 1300 kg/cm2 , the Safe load on the column, should not exceed
If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec
A reinforced concrete circular section of 50,000 mm2 cross-sectional area carries 6 reinforcing bars whose total area is 500 mm2. If the concrete is not to be stressed more than 3.5 MPa and modular ratio for steel and concrete is 18, the safe load the column can carry will be nearly
A steel column of ISHB 350 @72.4 kg/m is subjected to a factored axial compressive load of 2000 kN. The load is transferred to a concrete pedestal of grade M20 through square base plate. Consider the bearing strength of concrete as 0.45 fck, where fck is the characteristic strength of concrete. Using limit state method and neglecting the self-weight of base plate and steel column, the length of a side of the base plate to be provided is
Permeability in concrete is studied towards providing for, or guarding against, which of the following features? 1. The penetration by materials in solution may adversely affect the durability of concrete; moreover, aggressive liquids 'attack' the concrete. 2. In the case of reinforced concrete, ingress of moisture and air will result in corrosion of steel leading to an increase in the volume of steel, resulting in cracking and swilling of the concrete cover. 3. The moisture penetration depends on permeability and if the concrete can become saturated with water it is less vulnerable to frost action.
Consider the following statements for Euler’s equation to find the critical load of a column : 1. Critical load of a column is proportional to the flexural rigidity. 2. Critical load of a column depends upon yield stress. 3. Critical load of a column is inversely proportional to the length of the column. 4. Critical load of a column is inversely proportional to the square of the length of the column. Which of the above statements are correct?
If a rectangular under–reinforced section is subjected to bending moment equal to its moment carrying capacity and the stress in steel and extreme compression fiber of concrete at this moment are σs and σc respectively then which of the following is correct? Where, fy and fc are the permissible stresses in steel and concrete respectively.
“What is the different between height and radius of solid cylinder?” Which of the following option is sufficient alone to find the answer? A) A solid cylinder is made by melting a solid sphere. The radius of cylinder is 3 times the radius of a circle whose area is 154 sq.m. Height of cylinder is equal to the height of cone whose volume is 2772 cubic meters. B) Area of a rectangle whose longer side is ¾ times the radius of a solid cylinder, is 168 sq.m and, Volume of solid cylinder is 2772 cubic meters and its height is 18 m. C) A metallic cone of radius 15m and height 35m is melted into the solid cylinder of radius equal to the radius of a circle whose area is equal to the area of rectangle whose sides are in the ratio 4 : 3 respectively. D) The curved surface area of the solid cylinder is 3 time the surface area of a sphere of radius 7m and height of cylinder is equal to the height of a metallic cone whose curved surface area is 308 sq.m. 
Consider the following cases in the design of reinforced concrete members in flexure: 1. Over-reinforced section 2. Tension failure 3. Compression failure 4. Under-reinforced section Which of the above cases are considered for safe design of R.C. members in flexure?
According to load factor method, the permissible load ‘W’ on a short column reinforced with longitudinal bars and lateral stirrups, is