Related Questions

By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A 39.2%
B 48.8%
C 84.8%
D 88.4%
By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A 39.2%
B 48.8%
C 84.8%
D 88.4%
Saving of work done and power by fitting an air vessel to double acting reciprocating pump is of the order of
A 39.2%
B 49.2%
C 68.8%
D 84.8%
The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.
A Flow output
B Head developed
C Overall efficiency
D Weight
A double acting reciprocating pump compared to a single acting pump (of almost same size working under same pressure levels) would give almost double
A Head
B Discharge
C Efficiency
D None of these
একটি পানিপূর্ণ কুয়ার গভীরতা 20m ও ব্যাস 2 m. কুয়াটিকে পানি শূণ্য করার জন্য 5 HP এর একটি পাম্প লাগানো হল। অর্ধেক পানি তোলার পর পাম্পটি নষ্ট হয়ে গেল। বাকি পানি তোলার জন্য একই ক্ষমতা সম্পন্ন আর একটি পাম্প লাগানো হল। প্রথম পাম্প দ্বারা সম্পাদিত কাজের পরিমান নির্ণয় কর।(The depth and diameter of a water filled well are 20 m and 2 m respectively. An engine of 5 HP is attached to pump out the water. The pump was ruined after emptying half of the water. Then another pump of same capacity was attached to pump out rest of the water. Determine the work done by first pump.) 
A 2.54 × 104 J
B 1.44 × 104 J
C 2.34×104 J
D 1.54 × 104 J
E 1.54 ×104 J
At what value of crank angle (roughly), no flow of water from or into the air vessel takes place in case of a double acting reciprocating pump?
A 40° and 140°
B 45° and 60°
C 90° and 80°
D 20° and 120°
In a single stage, single acting reciprocating air compressor without clearance volume, the work-done is maximum during
A Isothermal compression
B Isentropic compression
C Polytropic compression
D None of these
In a single stage, single acting reciprocating air compressor, without clearance volume, the work-done is minimum during
A Isothermal compression
B Isentropic compression
C Polytropic compression
D None of these
The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)
A $${\text{m}}{\omega ^2}{\text{r}}\sin \theta $$
B $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
C $${\text{m}}{\omega ^2}{\text{r}}\frac{{\sin 2\theta }}{{\text{n}}}$$
D $${\text{m}}{\omega ^2}{\text{r}}\frac{{\cos2\theta }}{{\text{n}}}$$

Next steps