Related Questions

When a closely-coiled helical spring of mean diameter (D) is subjected to an axial load (W), the deflection of the spring ($$\delta $$) is given by (where d = Diameter of spring wire, n = No. of turns of the spring and C = Modulus of rigidity for the spring material)
A $$\frac{{{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
B $$\frac{{2{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
C $$\frac{{4{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
D $$\frac{{8{\text{W}}{{\text{D}}^3}{\text{n}}}}{{{\text{C}}{{\text{d}}^4}}}$$
A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be
A $$\frac{\tau }{2}$$
B $$\tau $$
C $$2\tau $$
D $$4\tau $$
Two closely coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is half that of spring 'B'. The ratio of deflections in spring 'A' to spring 'B' is
A $$\frac{1}{8}$$
B $$\frac{1}{4}$$
C $$\frac{1}{2}$$
D 2
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A $$\frac{{{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
B $$\frac{{2{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
C $$\frac{{4{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
D $$\frac{{8{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
Two closely-coiled helical springs 'A' and 'B' are equal in all respects but the number of turns of spring 'A' is double that of spring 'B'. The stiffness of spring 'A' will be __________ that of spring 'B'.
A One-sixteenth
B One-eighth
C One-fourth
D One-half
Two closely coiled helical springs 'A' and 'B' are equal in all respects but the diameter of wire of spring 'A' is double that of spring 'B' The stiffness of spring 'B' will be __________ that of spring 'A'
A One-sixteenth
B One-eighth
C One-fourth
D One-half
Two closely-coiled helical springs 'A' and 'B' of the same material, same number of turns and made from same wire are subjected to an axial load W. The mean diameter of spring 'A' is double the mean diameter of spring 'B'. The ratio of deflections in spring 'B' to spring 'A' will be
A $$\frac{1}{8}$$
B $$\frac{1}{4}$$
C 2
D 4
In leaf springs, the maximum bending stress developed in the plates is (where W = Load acting on the spring, $$l$$ = Span of the spring, n = Number of plates, b = Width of plates and t = Thickness of plates)
A $$\frac{{{\text{W}}l}}{{{\text{nb}}{{\text{t}}^2}}}$$
B $$\frac{{3{\text{W}}l}}{{2{\text{nb}}{{\text{t}}^2}}}$$
C $$\frac{{2{\text{W}}l}}{{{\text{nb}}{{\text{t}}^2}}}$$
D $$\frac{{3{\text{W}}l}}{{{\text{nb}}{{\text{t}}^2}}}$$
The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the
A Ability to absorb shock
B Capacity to store energy
C Ratio of the wire & coil diameters
D Load to produce unit deflection
10 g-এর একটি ভর ঘর্ষণহীন একটি অনুভূমিক তলের ওপর দিয়ে গিয়ে দেয়ালের সাথে সংযুক্ত একটি অনুভূমিক স্প্রিংকে 6 m/s বেগে আঘাত করে। যদি স্প্রিংটির স্প্রিং ধ্রুবকের মান 400 N/m হয় তাহলে এটিতে সর্বোচ্চ সংকোচন কত হবে? (A mass of 10 g sliding on a frictionless horizontal surface hits at 6 m/s on a horizontal spring attached to a wall. If the spring has a spring constant of 400 N/m, what is its maximum compression?)
A 0.3 cm
B 3 /√10cm
C 3 cm
D 0.9 cm

Next steps