Related Questions

According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
A 0.5
B 2
C $$\sqrt 2 $$
D $$\sqrt {\frac{3}{2}} $$
The maximum shear stress developed in a beam of circular section is __________ the average shear stress.
A Equal to
B $$\frac{4}{3}$$ times
C 1.5 times
D Twice
The maximum shear stress developed in a beam of rectangular section is __________ the average shear stress.
A Equal to
B $$\frac{4}{3}$$ times
C 1.5 times
D Twice
The ratio of maximum shear stress to average shear stress of a circular beam, is
A $$\frac{2}{3}$$
B $$\frac{3}{2}$$
C $$\frac{3}{4}$$
D $$\frac{4}{3}$$
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
When a body is subjected to a direct tensile stress ($${\sigma _{\text{x}}}$$) in one plane accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), the maximum shear stress is
A $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{{{\sigma _{\text{x}}}}}{2} - \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
C $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 - 4\tau _{{\text{xy}}}^2} $$
D $$\frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
The strain energy stored in a body due to shear stress, is (where $$\tau $$ = Shear stress, C = Shear modulus and V = Volume of the body)
A $$\frac{{\tau {\text{V}}}}{{2{\text{C}}}}$$
B $$\frac{{2{\text{C}}}}{{\tau {\text{V}}}}$$
C $$\frac{{{\tau ^2}{\text{V}}}}{{2{\text{C}}}}$$
D $$\frac{{2{\text{C}}}}{{{\tau ^2}{\text{V}}}}$$
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be
A $$\frac{\tau }{2}$$
B $$\tau $$
C $$2\tau $$
D $$4\tau $$
When a circular beam of diameter d is subjected to a shear force F, the maximum shear stress induced will be
A $$\frac{{4{\text{F}}}}{{\pi {{\text{d}}^2}}}$$
B $$\frac{{{\text{6F}}}}{{\pi {{\text{d}}^2}}}$$
C $$\frac{{{\text{8F}}}}{{\pi {{\text{d}}^2}}}$$
D $$\frac{{{\text{16F}}}}{{3\pi {{\text{d}}^2}}}$$

Next steps