Bissoy.com
Doctors Medicines MCQs Q&A

Consider as RS flip-flops with both inputs set to 0. If a momentary '1' is applied at the input S, then the output

Consider as RS flip-flops with both inputs set to 0. If a momentary '1' is applied at the input S, then the output Correct Answer Q will flip from 0 to 1

Related Questions

A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
In the question two statements are given, followed by two conclusions, I and II. You have to consider the statements to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statements. Statement I: Some flipflops are slippers Statement II: Some footwear are flipflops Conclusion I: All slippers are footwear Conclusion II: All footwear are slippers
In the question two statements are given, followed by two conclusions, I and II. You have to consider the statements to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statements. Statement I: Some flipflops are slippers Statement II: Some footwear are flipflops Conclusion I: All slippers are footwear Conclusion II: All footwear are slippers
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
One positive pulse with tw = 75 µs is applied to one of the inputs of an exclusive-OR circuit. A second positive pulse with tw = 15 µs is applied to the other input beginning 20 µs after the leading edge of the first pulse. Which statement describes the output’s relation with the inputs?
Consider the following statements: 1. Race-around condition occurs in a JK flipflop when the inputs are 1, 1 2. A flip-flop is used to store one bit of information 3. A transparent latch consists of D-type flipflops 4. Master-slave configuration is used in a flipflop to store two bits of information Which of the above statements are correct?
Consider a system whose input r and output y are related by the equation $$y\left( t \right) = \int\limits_{ - \infty }^\infty {x\left( {t - \tau } \right)} h\left( {2\tau } \right)d\tau $$
Signal Processing mcq question image
Where h(t) is shown in the graph
Which of the following four properties are possessed by the system? BIBO: Bounded input gives a bounded output
Causal: The system is causal.
LP : The system is low pass.
LTI: The system is linear and time-invariant.
A 1 to 8 demultiplexer with data input Din, address inputs S0, S1, and S2, (with S0  as the LSB) and Y̅0 to Y̅ 7 as the eight de-multiplexed output, is to be designed using two 2 to 4 decoders (with enable input E and address input A0 and A1) as shown in the figure. Din, S0, S1, and S2 are to be connected to P, Q, R, and S but not necessarily in this order. The respective input connections to P, Q, R, and S terminals should be
Consider the following statements regarding electromechanical devices: 1. A potentiometer has an input of rotation and an output of a potential difference. 2. An electric motor has an input of a potential difference and an output of rotation of a shaft. 3. A generator has an input of rotation of a shaft and an output of a potential difference Which of the above statements are correct?