Bissoy.com
Doctors Medicines MCQs Q&A

A sinusoidal voltage with a peak-to-peak value of 18 V is applied to an RC low-pass filter. If the reactance at the input frequency is zero, the output voltage is

A sinusoidal voltage with a peak-to-peak value of 18 V is applied to an RC low-pass filter. If the reactance at the input frequency is zero, the output voltage is Correct Answer Zero

Related Questions

If, Fhp(u, v)=F(u, v) – Flp(u, v) and Flp(u, v) = Hlp(u, v)F(u, v), where F(u, v) is the image in frequency domain with Fhp(u, v) its highpass filtered version, Flp(u, v) its lowpass filtered component and Hlp(u, v) the transfer function of a lowpass filter. Then, unsharp masking can be implemented directly in frequency domain by using a filter. Which of the following is the required filter?
A sinusoidal input voltage Vin of frequency ω is fed to the circuit shown in the figure, where C1 ≫ C2. If Vm is the peak value of the input voltage, then output voltage (Vout) is
Electronics mcq question image
Butterworth lowpass filter has a parameter, filter order, determining its functionality as very sharp or very smooth filter function or an intermediate filter function. If the parameter value is very high, the filter approaches to which of the following filter(s)?
Butterworth lowpass filter has a parameter, filter order, determining its functionality as very sharp or very smooth filter function or an intermediate filter function. If the parameter value is of lower order, the filter approaches to which of the following filter(s)?
Which of the following statements are correct? 1. A lowpass filter passes low frequencies and stops high frequencies. 2. A highpass filter passes high frequencies and rejects low frequencies 3. A bandpass filter passes frequencies within a frequency band and attenuates frequencies outside the band. 4. A bandstop filter passes frequencies within the band and blocks/attenuates frequencies outside a frequency band.
If Xl is leakage reactance, Xf is reactance due to field winding, Xdw is reactance due to damper winding and Xa is armature winding reactance then reactance of synchronous generator in subtransient state is due to which of the following?
The filter order of a Butterworth lowpass filter determines whether it is a very sharp or extremely smooth filter function, or an intermediate filter function. Which of the following filters does the filter approach if the parameter value is very high?
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
The same signal in Problem 2 is applied to an RC high-pass filter. If the reactance is zero at the input frequency, the output voltage is
A rotary drum filter with 30% submergence is used to filter concentrated aqueous slurry of calcium carbonate containing 15lb of solids per cubic foot of water. The pressure–drop is 2011Hg. If the filter cake contains 50% mixture (wet basis), calculate the filter area required to filter 10 gal/min of slurry. The filter cycle time is 5 min. The specific cake resistance depends on the pressure–drop as: α (ft/lb) = α (Δp)0.26, where α = 2.90×1010 Viscosity of the filtrate = 6.72×10-4 lb/ft-s. Density of calcium carbonate = 168.8 lb/ft3. Neglect filter medium resistance.