Related Questions

When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which (where, Fa is the load shared by each rivet due to axial load and Fm is the shearing load due to moment in any rivet.)
A Is at the maximum distance from CG of the rivet group
B Is at the minimum distance from CG of the rivet group
C Gives the maximum angle between the two forces Fa and Fm
D Gives the minimum angle between the two forces Fa and Fm
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A $$\frac{{{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
B $$\frac{{2{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
C $$\frac{{4{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
D $$\frac{{8{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
The frictional torque transmitted in a flat pivot bearing, considering uniform wear, is (where μ = Coefficient of friction, W = Load over the bearing and R = Radius of bearing surface)
A $$\frac{1}{2}$$μWR
B $$\frac{2}{3}$$μWR
C $$\frac{3}{4}$$μWR
D μWR
When the bearing is subjected to large fluctuations of load and heavy impacts, the bearing characteristic number should be _________ the bearing modulus.
A 10 times
B 5 times
C 15 times
D 20 times
According to Euler's column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends.
A Equal to
B Two times
C Four times
D Eight times
In the plate loading test for determining the bearing capacity of soil, the size of square bearing plate should be
A less than 300 mm
B between 300 mm and 750 mm
C between 750 mm and 1 m
D greater than 1 m
According to Euler's column theory, the crippling load for a column of length ($$l$$) with one end fixed and the other end hinged, is
A $$\frac{{{\pi ^2}{\text{E}}I}}{{{l^2}}}$$
B $$\frac{{{\pi ^2}{\text{E}}I}}{{4{l^2}}}$$
C $$\frac{{2{\pi ^2}{\text{E}}I}}{{{l^2}}}$$
D $$\frac{{4{\pi ^2}{\text{E}}I}}{{{l^2}}}$$
If p = bearing pressure on projected bearing area, Z = absolute viscosity of lubricant and N = speed of journal, then the bearing characteristic number is given by
A $$\frac{{{\text{ZN}}}}{{\text{p}}}$$
B $$\frac{{\text{p}}}{{{\text{ZN}}}}$$
C $$\frac{{\text{Z}}}{{{\text{pN}}}}$$
D $$\frac{{\text{N}}}{{{\text{Zp}}}}$$
A high vapour velocity is required for high plate efficiency in a seive plate coloumn. The satisfactory value of operating vapor velocity for design purpose in seive plate column is about __________ percent of the flooding velocity.
A 45
B 60
C 80
D 95
The type of bearing plate used in all joints and on curves to give better bearing area to the rails is
A flat mild steel bearing plate
B mild steel canted bearing plate
C cast iron anti creep bearing plate
D none of the above

Next steps