Bissoy.com
Doctors Medicines MCQs Q&A

If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall is more than 20, then the stiffening coefficient for wall proper will be

If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall is more than 20, then the stiffening coefficient for wall proper will be Correct Answer Greater than 1

Related Questions

Thickness of 8 tyres L, M, N, O, P, Q, R and S is compared. Thickness of no two tyres is same. Thickness of N is more than L but less than 6 tyres. Thickness of O is more than M but less than Q. Thickness of P is less than only two tyres. Thickness of Q is not more than P. Which of the following statement is not correct?
Dipu wants to paint all the four walls of his room. All the walls are of rectangular shape and opposite walls are of same measurement. If the size of the walls are 4 m x 3.5 m and 4.5 m × 3.5 m and cost to paint the wall is Rs. 22 per square meter, what will be the total cost to paint the walls?
All the forms of matter except gases emit electromagnetic radiation continuously. The gases which electrically or thermally excited emit a certain wavelength only, then which of the following is/are true about the process (i) The spacing between the atoms in the other forms of matter is high than in gas (ii) The spacing between the atoms in gases is high than the other forms of matter (iii) The energy of the emitted radiation depends on the spacing between the atoms (iv) The wavelength of the emitted radiation depends on the spacing between the atoms 
A cc slab of thickness 20 cm is constructed over a base of granular material with a modulus of reaction 10 kg/cm3. The maximum temperature differential between the top and bottom of the slab is found to be 19°C during summer day and night. The spacing between transverse joints is 8 m and the spacing between longitudinal joints is 4 m. The design wheel load is 5100 kg, radius of contact area is 15 cm, Poisson’s ratio is 0.15, modulus of elasticity is 3×105 kg/cm2, the thermal coefficient is 10 ×10-6 /°C and the coefficient of friction is 1.5. Using the above information, find the worst combination of stresses at the edge of the pavement.
The growth rate of pearlite, v, and the interlamellar spacing S are given by the following relation, $$v = k.\frac{1}{S}\left( {\frac{{1 - {S_c}}}{S}} \right)$$    where Sc is the critical spacing at which the growth rate is zero and k is a materials constant. The actual interlamellar spacing observed will correspond to
P, Q, R, Sand T are five crops that Babu grows. T is fast growing and more water demanding than R which gives more yield than T. P gives more yield than R and grows faster than Q. Q is more water demanding than T but is second lowest yielder, S is the slowest growing and least water demanding of all crops but gives highest yield. R is more water demanding and grows faster than P. Select the crop or crops that has/ have as many as crops that are more water demanding and as many as crops that give less yield than it. 
There are eight cars A, B, C, D, E, F, G and H. Each car has a different price. Price of C is more than that of A and D. Price of at least two cars is less than A. Price of F is more than that of G and H. Price of D is less than G, but more than E. Price of B is less than H, but more than G. Price of at least four cars is more than that of C. Which of the following sequence is correct?
Load-bearing walls are defined as those walls which carry their own weight only whereas non-load bearing walls are defined as those walls which can carry superimposed loads in addition to their own weight.
Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than
A composite wall is made of two layers of thickness δ1 and δ2 having thermal conductivities k and 2k and equal surface area normal to the direction of heat flow. The outer surface of composite wall are at 100 degree Celsius and 200 degree Celsius. The minimum surface temperature at the junction is 150 degree Celsius. What will be the ratio of wall thickness?