Related Questions

In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on
A Front face only
B Inner face only
C Both front face and inner face
D None of the above
A simply supported beam A carries a point load at its mid span. Another identical beam B carries the same load but uniformly distributed over the entire span. The ratio of the maximum deflections of the beams A and B, will be
A $$\frac{2}{3}$$
B $$\frac{3}{2}$$
C $$\frac{5}{8}$$
D $$\frac{8}{5}$$
When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies
A Less than the left half span
B Whole of left half span
C More than the left half span
D Whole span
If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than
A $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
B $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} + \frac{{2{\text{D}}}}{3}} \right)^2}$$
C $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
D $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{\text{D}}}{3}} \right)^2}$$
For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is
A 0.6
B 0.7
C 0.8
D 0.9
The slab is designed as one way if the ratio of long span to short span is
A Less than 1
B Between 1 and 1.5
C Between 1.5 and 2
D Greater than 2
The transverse reinforcements provided at right angles to the main reinforcement
A Distribute the load
B Resist the temperature stresses
C Resist the shrinkage stress
D All the above
কাগজের ভার হিসাবে ব্যবহৃত একটি পুরু কাচ (প্রতিসরাঙ্ক 1.5) খন্ডের উপর থেকে খাড়া নীচের দিকে তাকালে কাগজের উপর একটি দাগ কাচের উপর প্রান্ত থেকে 6 cm নীচে দেখা যায়। কাচ খন্ডতির পুরুত্ব কত? (When you look downward from the top of a thick glass (refractive index 1.5) slab used as a paper weight, a mark on the paper is seen 6 cm below from the top of the slab. What is the thickness of the glass slab?)
A 4 cm
B 6 cm
C 9 cm
D 12 cm
কাগজের ভার হিসাবে ব্যবহৃত একটি পুরু কাচ (প্রতিসরাঙ্ক 1.5) খণ্ডের উপর থেকে খাড়া নীচের দিকে তাকালে কাগজের উপর একটি দাগ কাচের উপর প্রান্ত থেকে 6 cm নীচে দেখা যায়। কাচ খন্ডটির পুরুত্ব কত? (When you look downward from the top of a thick glass (refractive index 1.5) slab used as a paper weight, a mark on the paper is seen 6 cm below from the top of the slab. What is the thickness of the glass slab?)
A 4 cm
B 6 cm
C 9 cm
D 12 cm
The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than
A 4 mm
B 5 mm
C 6 mm
D 7 mm

Next steps