Related Questions

When a shaft, is subjected to torsion, the shear stress induced in the shaft varies from
A Minimum at the center to maximum at the circumference
B Maximum at the center to minimum at the circumference
C Zero at the center to maximum at the circumference
D Maximum at the center to zero at the circumference
A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is
A $$\frac{{\text{M}}}{{\text{T}}}$$
B $$\frac{{\text{T}}}{{\text{M}}}$$
C $$\frac{{2{\text{M}}}}{{\text{T}}}$$
D $$\frac{{2{\text{T}}}}{{\text{M}}}$$
Two shafts ‘A’ and ‘B’ under pure torsion are of identical length and identical weight and are made of the same material. The shaft ‘A’ is solid and the shaft ‘B’ is hollow. We can say that
A Shaft B is better than shaft A
B Shaft A is better than shaft B
C Both the shafts are equally good
D None of these
Two shafts A and B are made of the same material. The diameter of shaft A is twice as that of shaft B. The power transmitted by the shaft A will be __________ of shaft B.
A Twice
B Four times
C Eight times
D Sixteen times
The strain energy stored in a body due to shear stress, is (where $$\tau $$ = Shear stress, C = Shear modulus and V = Volume of the body)
A $$\frac{{\tau {\text{V}}}}{{2{\text{C}}}}$$
B $$\frac{{2{\text{C}}}}{{\tau {\text{V}}}}$$
C $$\frac{{{\tau ^2}{\text{V}}}}{{2{\text{C}}}}$$
D $$\frac{{2{\text{C}}}}{{{\tau ^2}{\text{V}}}}$$
The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to
A $$\frac{{\text{T}}}{2}$$
B 1T
C 2T
D 4T
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
The maximum shear stress developed in a beam of circular section is __________ the average shear stress.
A Equal to
B $$\frac{4}{3}$$ times
C 1.5 times
D Twice
The ratio of maximum shear stress to average shear stress of a circular beam, is
A $$\frac{2}{3}$$
B $$\frac{3}{2}$$
C $$\frac{3}{4}$$
D $$\frac{4}{3}$$
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$

Next steps