Bissoy.com
Doctors Medicines MCQs Q&A

Determine Flat plate skin friction coefficient if Reynolds number is 123500. Consider flow to be laminar.

Determine Flat plate skin friction coefficient if Reynolds number is 123500. Consider flow to be laminar. Correct Answer 0.0038

Laminar flow flat plate skin friction coefficient = 1.328 / (Reynolds number0.5) = 1.328 / (1235000.5) = 0.0038.

Related Questions

A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
The average drag coefficient for turbulent boundary layer flow past a thin plate is given by C f = 0.455/ (log 10 R el) 2.58 Where R el is the Reynolds number based on plate length. A plate 50 cm wide and 5 m long is kept parallel to the flow of water with free stream velocity 3 m/s. Calculate the drag force on both sides of the plate. For water, kinematic viscosity = 0.01 stokes
Ambient air at 20 degree Celsius flows past a flat plate with a sharp leading edge at 3 m/s. The plate is heated uniformly throughout its entire length and is maintained at a surface temperature of 40 degree Celsius. Calculate the distance from the leading edge at which the flow in the boundary layer changes from laminar to turbulent conditions. Assume that transition occurs at a critical Reynolds number of 500000
Consider the following statements: 1) At low Reynolds numbers of any flow, viscous forces dominate over inertial forces. 2) Transition from laminar to turbulent flow occurs over a range of Reynolds numbers depending on the surface presented to the flow. Which of the above statements is/are correct?
Six flats A, B, C, D, E and F are located in two rows of three flats each. The flats in both the rows face each other. Flat D is diagonally opposite to flat C. Flat E is opposite to flat F, which is north facing. Flat C is 2nd to the left of A and both of flats are south facing. Which of the following flats is facing flat B?
A flat plate was positioned at zero incidence in a uniform flow stream of air. Assuming boundary layer to be turbulent over the entire plate, workout the ratio of skin-friction forces on the front and rear half part of the plate
Which of the following is NOT true about Frictional force? A. Friction is the force which opposes the relative motion of two surfaces in contact. B. The force of friction that acts when a body is moving (sliding) on a surface is called sliding friction. C. Friction in machines wastes energy and also causes wear and tear. D. Rolling friction is much more than sliding friction, the use of ball bearings in a machine considerably reduces friction.
Study the statements listed below (1) Negative skin friction is developed when the pile is driven through a recently deposited clay layer (2) Negative skin friction is developed when the pile is driven through a layer of dense sand (3) Negative skin friction is developed due to sudden drawdown of the water table Out of these statements
Which of the following statements is/are CORRECT regarding the flow of fluid? a) All fluid layers are parallel to each other in case of turbulent flow. b) The Reynold’s number is less than 2000 for turbulent flow and greater than 4000 for laminar flow. c) Two fluid layers don’t cross each other in case of laminar flow