Bissoy.com
Doctors Medicines MCQs Q&A

A flat plate was positioned at zero incidence in a uniform flow stream of air. Assuming boundary layer to be turbulent over the entire plate, workout the ratio of skin-friction forces on the front and rear half part of the plate

A flat plate was positioned at zero incidence in a uniform flow stream of air. Assuming boundary layer to be turbulent over the entire plate, workout the ratio of skin-friction forces on the front and rear half part of the plate Correct Answer 1.347

F 1/F 2 = 0.574/1 – 0.574 = 1.347.

Related Questions

The boundary layer thickness at a distance of l m from the leading edge of a flat plate, kept at zero angle of incidence to the flow direction, is O.l cm. The velocity outside the boundary layer is 25 ml sec. The boundary layer thickness at a distance of 4 m is (Assume that boundary layer is entirely laminar)
A flat plate 1 m by 1 m is placed in a wind tunnel. The velocity and temperature of free stream air are 80 m/s and 10 degree Celsius. The flow over the whole length of the plate is made turbulent by turbulizing grid placed upstream of the plate. Find the thickness of the hydrodynamic boundary layer at trailing edge of the plate
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the moles of nitrogen entering the reactor and in the recycle stream?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the number of moles, moles of inerts and moles of hydrogen in the recycle stream?
A circular queue has been implemented using a singly linked list where each node consists of a value and a single pointer pointing to the next node. We maintain exactly two external pointers FRONT and REAR pointing to the front node and the near node of the queue, respectively. Which of the following statements is/are CORRECT for such a circular queue, so that insertion and deletion operations can be performed in O(1) time? I. Next pointer of front node points to the rear node. II. Next pointer of rear node points to the front node.
A small thermo-couple is positioned in a thermal boundary layer near a flat plate past which water flows at 30 degree Celsius and 0.15 m/s. The plate is heated to a surface temperature of 50 degree Celsius and at the location of the probe, the thickness of thermal boundary layer is 15 mm. If the temperature profile as measured by the probe is well-represented by t – t S/t INFINITY – t S = 1.5 (y/δ t) – 0.5 (y/δ t) 3 Determine the heat flux from plate to water
A flat plate 1 m by 1 m is placed in a wind tunnel. The velocity and temperature of free stream air are 80 m/s and 10 degree Celsius. The flow over the whole length of the plate is made turbulent by turbulizing grid placed upstream of the plate. Find the heat flow from the surface of the plate
The average drag coefficient for turbulent boundary layer flow past a thin plate is given by C f = 0.455/ (log 10 R el) 2.58 Where R el is the Reynolds number based on plate length. A plate 50 cm wide and 5 m long is kept parallel to the flow of water with free stream velocity 3 m/s. Calculate the drag force on both sides of the plate. For water, kinematic viscosity = 0.01 stokes