The value of the geometric parameter for a plate of width w loaded in tension with the centrally loaded crack of the length 2a __________ 1/2 b) 1/2 c) d)

The value of the geometric parameter for a plate of width w loaded in tension with the centrally loaded crack of the length 2a __________ 1/2 b) 1/2 c) d) Correct Answer 1/2

The geometric parameter value depends upon the shape and size of the crack length. In general, it is denoted by α, and for the plate of width w loaded in the tension, it is given as the -> 1/2.
Bissoy MCQ

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
A tension crack of 5 m depth behind a rock slope crest is completely filled with water. What is the horizontal force exerted on a unit slope length by the water in the tension crack?
According to Irwin’s correction of plasticity at the crack tip, the sufficient crack length is given as the actual crack length plus the radius of the plastic zone. The radius of the plastic zone (rp) in case of plane stress is given as ________
According to Irwin’s correction of plasticity at the crack tip, the effective crack length is given as the actual crack length plus the radius of the plastic zone. The radius of the plastic zone (rp) in case of plane strain is given as ________
The young’s modulus of the steel is 600 MPa, and the plastic stress required to extend the crack is 50*10-9, and the initial crack length is 2 microns. Find the fracture stress required to crack the material?
The crack propagation rate with stress is given as ______ Where; -> da/dN is crack growth with each cycle -> C is constant -> σm is mean stress -> σa is alternating stress -> a is the crack length -> m and n are constant
Two plates are joined by double strap butt joints with rivets arrangement as shown in the figure. Width of the plate is 300mm and diameter of rivets 30mm. The thickness of the plates can be taken as 20mm. Allowable stress in tension, shear and compression are 80 N/mm²,60 N/mm² and 160N/mm². If width of plate=80mm and diameter of rivets 10mm, then pitch will be?
Mrs. Carson took a taxi to meet her three friends for lunch. They were waiting for her outside the restaurant when she pulled up in the car. She was so excited to see her friends that she left her tote bag in the taxi. As the taxi pulled away, she and her friends took notice of the license plate number so they would be able to identify the car when they called the taxi company.

#1 : The four women seem to agree that the plate starts out with the letter J.
#2 : Three of them agree that the plate ends with 12L.
#3 : Three of them think that the second letter is X, and a different three think that the third letter is K.

The four license plate numbers below represent what each of the four women thinks she saw. Which one is most likely the license plate number of the taxi?
Atmospheric air at 30 degree Celsius temperature and free stream velocity of 2.5 m/s flows along the length of a flat plate maintained at a uniform surface temperature of 90 degree Celsius. Let length = 100 cm, width = 50 cm and thickness = 2.5 cm. Thermal conductivity of the plate material is 25 W/m K, find heat lost by the plate
The maximum harbour depth below lowest low water is generally equal to
(i) loaded draft + 1.2 m when bottom is rock
(ii) loaded draft + 1.8 m when bottom is soft
(iii) loaded draft + 1.2 m when bottom is soft
(iv) loaded draft + 1.8 m when bottom is rock