Bissoy.com
Doctors Medicines MCQs Q&A

In the following torsional test sample, the highest shear stress will be at point ________

In the following torsional test sample, the highest shear stress will be at point ________ Correct Answer D

The shear stress will be zero in the center of the cylinder, and it will be maximum at the circumference or the surface of the cylinder. So, in this case, at point D, the shear stress will be maximum.

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
How far is point 'R' from Point 'T'? Statement (I): Point 'R' is 5 metres to the north of point 'M'. Point 'U' is 4 metres to the east of point 'R'. Point 'T' is to the west of point 'R' such that points 'U' 'R' and 'T' form a straight line of  metres. Statement (II): Point 'Z' is metres to the south of point 'T'. Point 'U' is  metres to the east of point 'T'. Point 'M' is  metres to the east of point 'Z'. Point 'R' is  metres to the north of point 'M'. Point 'R' lies on the line formed by joining points 'T' and 'U'.
Point A is 3m in the north of point B. Point D is 2m in the east of point E. Point F is 9m in the west of point G. Point C is 4m in the west of point B. Point C is 3m in the south of point D. Point F is 5m in the south of point E. Point H is 5m in the north of point G. What is the shortest distance between point H and point A?
Point P is 4m in the west of point V. Point R is 6m in the north of point Q. Point T is 5m in the south of point S. Point V is in the middle of point R and Q. Point U is 5m in the east of point R. Point V is in north of point Q. Point S is 5m in the east of point V. What is the area of triangle formed by point P, R and Q?
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. How far and in which direction is Point G from Point A?
Study the following information and answer the questions. Point A is 8m to the west of Point B. Point C is 4m to the south of Point B. Point D is 4m to the east of Point C. Point F is 6m to the north of Point D. Point E is 8m to the west of Point F. Point G is 2m to the south of Point E. If point G is 4m to the north of Point H, then what is the distance between H and D?
Garima starts walking towards the south from point R. He walks for 5m to reach Point S then turns right and walks for 2m to reach point T from there he turns left and walks for 3m to reach Point Z. He then turns right from point Z and walks for 6m to reach point Y and then turns right and walks for 3m to reach point X. He then turns right from point X and walks for 4m to reach point W and then turns left and walks for 5m to reach point V and then turns left and walks for 4m till point U and stops. What is the shortest distance between point V and point R?
The Rheological behaviour of concrete, when represented by shear stress vs rate of shear, is characterized as Where : τ shear stress, Τ0 = (initial) yield value, μ = at-point plastic viscosity, γ̇ = at point rate of shear.
Consider the following statements: 1. The water content of a soil remains unchanged during entire duration of a ‘quick test. 2. Effective stress cum shear parameters of clay can be obtained from drained triaxial shear test. 3. Strain-controlled shear test is a good option since this test procedure maintains better control on the rate of loading than other tests. Which of the above statements is/ are correct?
Which of the following factors are affecting critical shear stresses? 1. Purity of metals reduces the critical shear stress 2. Surface films greatly enhance the critical shear stress 3. Rise in temperature 4. Rate of deformation and the extent of initial deformation also help in raising the critical shear stress