Bissoy.com
Doctors Medicines MCQs Q&A

Why are Packed bed Heat Exchangers Direct contact type heat exchangers?

Why are Packed bed Heat Exchangers Direct contact type heat exchangers? Correct Answer Gas liquid system where they are brought to direct contact

Packed bed Heat Exchangers are called Direct contact type heat exchangers because they usually bring two immiscible fluids to direct contact to exchange heat, in packed beds the most common use is that of Gas-Liquid systems.

Related Questions

Bed bugs are parasitic insects in the genus Cimex that feed exclusively on blood. Cimex lectularius, the common bed bug, is the best known as it prefers to feed on human blood. The name bed bug derives from the preferred habitat of Cimex lectularius: warm houses and especially near or inside beds or other sleep areas. Bed bugs are mainly active at night, but are not exclusively nocturnal. They usually feed on their hosts without being noticed. A number of adverse health effects may results from bed bug bites, including skin rashes, psychological effects, and allergic symptoms. Bed bugs are not known to transmit any pathogens as disease vectors. Certain signs and symptoms suggest the presence of bed bugs; finding the adult insects confirms the diagnosis. Assuming the information in the given paragraph is true, choose the correct statement.
Indirect contact heat exchangers are preferred over direct contact heat exchangers, because
A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below:
Δ P/L = 375 × 103 VOM + 10.94 × 106 V2OM (SI units)
If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed?
Kelly and Chris packed several boxes with books. If Chris packed 60 percent of the total number of boxes, what was the ratio of the number of boxes Kelly packed to the number of boxes Chris packed?
If "blanket" is called "towel","towel" is called "bed sheet", "bed sheet" is called "pillow" ,"pillow" is called "bed" and "bed" is called "table". What is used to cover bed?
The statements below are followed by two conclusions labeled I and II. Assuming that the information in the statements is true, even if it appears to be at variance with generally established facts, decide which conclusion(s) logically and definitely follow(s) from the information given in the statements. Statements: All bed is bed sheet. No bed is blanket. Some blanket is comforter Conclusion I: No comforter is bed. Conclusion II: Some blanket is bed sheet.
Consider the following statements: In case of helical gears, teeth are cut at an angle to the axis of rotation of the gears. 1) Helix angle introduces another ratio called axial contact ratio. 2) Transverse contact ratio is equal to axial contact ratio in helical gears. 3) Large transverse contact ratio does not allow multiple teeth to share the load. 4) Large axial contact ratio will cause larger axial force component Which of the above statements are correct?
Are these statements about the regenerative heat exchangerstrue? Statement 1: Regenerators are commonly used in gas/gas heat recovery applications. Statement 2: Regenerative heat exchangers are also known as capacitive heat exchangers.
Which of the following statements about two-phase heat exchangers are correct? Statement 1: Two-phase heat exchangers undergo phase change during the heat transfer process. Statement 2: It is used mainly in water-to-water heat transfer applications.
The important design and operating considerations for Extended-Surface Compact Heat Exchangers are: (1) Both fluids may have high or low heat transfer coefficients (2) As the tubes are very narrow (low DH), the fluid used should not be corrosive as effective cleaning of tubes is not possible. (3) The fluid pressure drop calculation is important as a regulatory method to ensure long life of the tubes. (4) Unlike shell and tube type heat exchangers, these are limited when it comes to operating pressure and temperature.