Bissoy.com
Doctors Medicines MCQs Q&A

What kind of misfit arises if the inclusion is the wrong size for the hole it is located?

What kind of misfit arises if the inclusion is the wrong size for the hole it is located? Correct Answer Volume misfit

When the inc1usion is incoherent with the matrix, there is no attempt at matching the two lattices and lattice sites are not conserved across the interface. Under these circumstances there are no coherency strains. Misfit strains can, however, still arise if the inclusion is the wrong size for the hole it is located in. In this case the lattice misfit has no significance and it is better to consider the volume misfit.

Related Questions

A spacing ‘’D’’ can be used to completely accommodate the lattice misfit in the one direction without any long-range strain field by a set of edge location. Calculate the value of D if the interplanar spacing’s of matching planes are given as 20mm, 19mm respectively? (Assume the misfit to be very small)
For manufacturing of a certain amount of hole, maximum hole size was found to be 50.14 mm and minimum hole size was found to be 49.98. What will be the Tolerance in mm?
For manufacturing of a certain amount of hole, maximum hole size was found to be 50.14 mm and minimum hole size was found to be 49.98. Tolerance in mm will be
Pipe A along with a hole can fill a tank in 20 minutes, pipe B along with hole can fill that tank in 1 hour. If both the pipes along with hole can fill that tank in (60/7) minutes, then what is the time taken by hole alone to empty that tank completely?
In this question, a passage and a related statement have been given. Read the passage carefully and assess the statement based on it. Using knives and screws, two Russian astronauts on Tuesday took a sample of substance around a mysterious cavity of the spacecraft called the Soyuz, which was placed in the International Space Station, a Moscow official suggested that it was a break - It can also be done. In August, two months after the last visit of the vehicle, the air leak was detected in the Soyuz spacecraft due to the 2 mm air in the ISS. Roskosmos, an astronomical institute, says that cutting off the insulation on the hole and sampling the material around it and the purpose of putting a new insulation on it is to find out that this small but dangerous hole has been done on earth or Is in space. The chief of Roskosmos has said that the error of manufacturing has not been found in the investigation. Experienced astronauts had to struggle but they managed their mission. Before the spacewalk, astronauts were able to inspect the hole just from within the spacecraft. The biggest difficulty was that in the Soyuz spacecraft, the ISS was not designed to improve during adverse weather space, and no railing was also made to catch the space passengers outside the vehicle. Statement: The mysterious hole in the So yuz spacecraft was due to the error of manufacturing. Select the appropriate from the given options A - Statement is completely true B - The statement is possibly true C - the statement can not be determined D - Statement is completely false
Consider the following statements regarding limits and fits 1. Actual size is the standard size for the part and is the same both for the hole and its shaft. 2: Basic size is the dimension as measured on the manufactured part. 3. Deviation is the algebraic difference between a size and the corresponding basic size. Which of the above statements is/are correct ? 
S1: There were no finger prints anywhere.
P: First of all it was impossible even for a child to enter through the hole in the roof.
Q: When the investigators tried to reconstruct the crime, they came up against facts.
R: Moreover, when the detectives tried to push a silver vase, it was found to be double the sizeof the hole.
S: Again, the size of the hole was examined by the experts who said that nothing had been passed through it.
S6: These conclusions made the detectives think that it was a fake theft.

The Proper sequence should be:
Which of the following statements are true with regards to the selection of a sample size? (i) The sample size (n) may be a fixed percentage of lot size (N). (ii) The sample size (n) may be kept constant irrespective of lot size (N). (iii) Sample size (n) can be selected at the personal whim of the inspector.
For both coherent and incoherent inclusion the misfit strain energy is proportional to____
If μ is the shear modulus of the matrix and V is the volume of the unconstrained hole in the matrix and the elastic energy does not depend on the shape of the precipitate, if so, calculate the elastic strain energy? (Assume the poissons ratio to be 1/3 and Misfit-Δ)