Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Consider the following statements with reference to Jet stream. 1. The Jet Stream is a geostrophic wind. 2. There are two permanent jet streams – subtropical jets at mid-latitudes and polar front jets at lower latitudes. 3. Temperature also influences the velocity of the jet stream. The lower the difference in air temperature, the faster the jet stream. Which of the statements given above is/are NOT correct?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the moles of nitrogen entering the reactor and in the recycle stream?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream, and calculate the number of moles, moles of inerts and moles of hydrogen in the recycle stream?
The fresh feed to an ammonia synthesis reactor contains nitrogen, hydrogen and 2.0 mole per cent inerts. The molar ratio of H2:N2 is 3:1. The product stream consists of pure ammonia. Since conversion in the reactor is only 15%, a recycle stream is used and in order to avoid build-up of inerts, a purge stream is withdrawn. The rate of purge stream is adjusted to keep inert concentration in the recycle stream at 8 mole per cent. For a fresh feed rate of 100 moles/hr. Note that recycle stream contains only nitrogen, hydrogen and inerts. The N2:H2 ratio of 1:3 is maintained in every process stream. Calculate the moles of ammonia produced.
The following question, there are three statements I, II and III. Read the question carefully and mark your answer according to which statements(s) is/are sufficient to the answer the question. What is the Speed of the stream? Statement I: The distance between two points A and B is a km and the boat cover 90km along the stream in 5 hours. Statement II: The distance travelled along the stream is four times the total distance and that against the stream is three times the total distance Statement III: The total time taken against the stream is 10% more than that along the stream
Arrange the processes in the increasing order of their maximum material removal rate. Electrochemical Machining (ECM) Ultrasonic Machining (USM) Electron Beam Machining (EBM) Laser Beam Machining (LBM) and Electric Discharge Machining (EDM)
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
A jet of water is striking at the centre of a curved vane moving with a uniform velocity in the direction of jet. For the maximum efficiency, the vane velocity is ________ of the jet velocity
Water, having a density of 1000 kg/m3, leave from a nozzle with a velocity of 10 m/s and the jet strikes a bucket mounted on a Pelton wheel. The wheel rotates at 10 rad/s. The mean diameter of the wheel is 1 m. The jet is split into two equal streams by the bucket, such that each stream is deflected by 120°, as shown in the figure. Friction in the bucket may be neglected. Magnitude of the torque exerted by the water on the wheel, per unit mass flow rate of the incoming jet, is
In Abrasive water jet machining, how are the abrasives fed into the water jet stream?