Hot air at 50°C. If the forced heat transfer convection is 75 W/m2K, the heat gain rate gain rate by the plate through an area of 2m2 will be _____

Hot air at 50°C. If the forced heat transfer convection is 75 W/m2K, the heat gain rate gain rate by the plate through an area of 2m2 will be _____ Correct Answer 15KW

Rate of heat transfer Q = Q = hA∆T Q = 75×2×(150-50) Q = 15 kW.
Bissoy MCQ

Related Questions

A hot plate of 15 cm2 area maintained at 200 degree celsius is exposed to still air at 30 degree Celsius temperature. When the smaller side of the plate is held vertical, convective heat transfer rate is 15 per cent higher than bigger side of the plate is held vertical. Find size of the plate. The appropriate correlation for the convection coefficient is Nu = 0.60 (Gr Pr) 0.25
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
Consider the following phenomena (i) Boiling (ii) Free convection in air (iii) Forced convection in air (iv) Conduction in air Identify the correct sequence (heat transfer coefficient)
Forced air flows over a convection heat exchanger in a room heater, resulting in a convective heat transfer coefficient 1.136 k W/m2 K. The surface temperature of heat exchanger may be considered constant at 65 degree Celsius, and the air is at 20 degree Celsius. Determine the heat exchanger surface area required for 8.8 k W of heating
To effect a bond between two metal plates, 2.5 cm and 15 cm thick, heat is uniformly applied through the thinner plate by a radiant heat source. The bonding must be held at 320 K for a short time. When the heat source is adjusted to have a steady value of 43.5 k W/m2, a thermocouple installed on the side of the thinner plate next to source indicates a temperature of 345 K. Calculate the temperature gradient for heat conduction through thinner plate. In the diagram, the upper plate is 2.5 cm thick while the lower is 15 cm thick.
A finned surface consists of root or base area of 1m2 and fin surface area of 2m2. The average heat transfer coefficient for finned surface is 20W/m2K effectiveness of fins provided is 0.75. If finned surface with surface with root or base temperature of 50°C is transferring heat to fluid of 30°C, then the rate of heat transfer without using fin is _______
A thin metal plate of 4 cm diameter is suspended in atmospheric air whose temperature is 290 K. This plate attains a temperature of 295 K when one of its faces receives radiant energy from a heat source at the rate of 2 W. If heat transfer coefficient on both surfaces of the plate is stated to be 87.5 W/m 2 K, workout the reflectivity of the plate.
A thin metal plate of 4 cm diameter is suspended in atmospheric air whose temperature is 290 K. This plate attains a temperature of 295 K when one of its face receives radiant energy from a heat source at the rate of 2 W. If heat transfer coefficient on both surfaces of the plate is stated to be 87.5 W/m 2 K, workout the reflectivity of the plate
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
A heat treat steel plate measures 3 m by 1 m and is initially at 30 degree Celsius. It is cooled by blowing air parallel to 1 m edge at 9 km/hr. If the air is at 10 degree Celsius. Estimate the convection heat transfer from both sides of the plate