Bissoy.com
Doctors Medicines MCQs Q&A

A heat treat steel plate measures 3 m by 1 m and is initially at 30 degree Celsius. It is cooled by blowing air parallel to 1 m edge at 9 km/hr. If the air is at 10 degree Celsius. Estimate the convection heat transfer from both sides of the plate

A heat treat steel plate measures 3 m by 1 m and is initially at 30 degree Celsius. It is cooled by blowing air parallel to 1 m edge at 9 km/hr. If the air is at 10 degree Celsius. Estimate the convection heat transfer from both sides of the plate Correct Answer 747.6 W

Q = h A d t, h = Nu k/d.

Related Questions

A nuclear reactor with its core constructed of parallel vertical plates 2.25 m high and 1.5 m wide has been designed on free convection heating of liquid bismuth. Metallurgical considerations limit the maximum surface temperature of the plate to 975 degree Celsius and the lowest allowable temperature of bismuth is 325 degree Celsius. Estimate the maximum possible heat dissipation from both sides of each plate. The appropriate correlation for the convection coefficient is Nu = 0.13 (Gr Pr) 1/3
The engine oil at 150 degree Celsius is cooled to 80 degree Celsius in a parallel flow heat exchanger by water entering at 25 degree Celsius and leaving at 60 degree Celsius. Estimate the number of transfer units
In a food processing plant, a brine solution is heated from – 12 degree Celsius to – 65 degree Celsius in a double pipe parallel flow heat exchanger by water entering at 35 degree Celsius and leaving at 20.5 degree Celsius. Let the rate of flow is 9 kg/min. Estimate the area of heat exchanger for an overall heat transfer coefficient of 860 W/m2 K. For water c P = 4.186 * 10 3 J/kg K
A 2 cm thick steel slab heated to 525 degree Celsius is held in air stream having a mean temperature of 25 degree Celsius. Estimate the time interval when the slab temperature would not depart from the mean value of 25 degree Celsius by more than 0.5 degree Celsius at any point in the slab. The steel plate has the following thermal physical properties Density = 7950 kg/m3 C P = 455 J/kg K K = 46 W/m K
The engine oil at 150 degree Celsius is cooled to 80 degree Celsius in a parallel flow heat exchanger by water entering at 25 degree Celsius and leaving at 60 degree Celsius. Estimate the exchanger effectiveness
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
Exhaust gases (c P = 1.12 k J/kg K) flowing through a tubular heat exchanger at the rate of 1200 kg/hr are cooled from 400 degree Celsius to 120 degree Celsius. This cooling is affected by water (c P = 4.18 k J/kg K) that enters the system at 10 degree Celsius at the rate of 1500 kg/hr. If the overall heat transfer coefficient is 500 k J/m2 hr degree, what heat exchanger area is required to handle the load for parallel flow arrangement?
Air at 20 degree Celsius flows over a flat plate maintained at 75 degree Celsius. Measurements shows that temperature at a distance of 0.5 mm from the surface of plate is 50 degree Celsius. Presuming thermal conductivity of air is 0.0266 W/m K, estimate the value of local heat transfer coefficient
A horizontal heated plate at 200 degree Celsius and facing upwards has been placed in still air at 20 degree Celsius. If the plate measures 1.25 m by 1 m, make calculations for the heat loss by natural convection. The convective film coefficient for free convection is given by the following empirical relation h = 0.32 (α) 0.25 W/m2 K Where α is the mean film temperature in degrees kelvin