Bissoy.com
Doctors Medicines MCQs Q&A

Threads are classified into V thread, Acme thread, Knuckle thread, etc. on the basis of _________

Threads are classified into V thread, Acme thread, Knuckle thread, etc. on the basis of _________ Correct Answer profile of the groove

On the basis of the profile of the groove, threads are classified as V thread, Acme thread, Knuckle thread, Buttress thread, Square thread, etc. On the basis of start of threads, threads are classified as single start, double start, triple start, etc.

Related Questions

User level threads are threads that are visible to the programmer and are unknown to the kernel. The operating system kernel supports and manages kernel level threads. Three different types of models relate user and kernel level threads. Which of the following statements is/are true ? (a) (i) The Many - to - one model maps many user threads to one kernel thread (ii) The one - to - one model maps one user thread to one kernel thread (iii) The many - to - many model maps many user threads to smaller or equal kernel threads (b) (i) Many - to - one model maps many kernel threads to one user thread (ii) One - to - one model maps one kernel thread to one user thread (iii) Many - to- many model maps many kernel threads to smaller or equal user threads
Which of the following threads is used for transmission of power? I. Square thread II. Buttress thread III. Acme thread Choose the correct answer from the options given below
Consider the following multi-threaded code segment (in a mix of C and pseudocode), invoked by two processes P1 and P2, and each of the processes spawns two threads T1 and T2: int x = 0; // global Lock L1; // global main() { create a thread to execute foo(); // Thread T1 create a thread to execute foo(); // Thread T2 wait for the two threads to finish execution; print (x);} foo() { int y = 0; Acquire L1; x = x + 1; y = y + 1; Release L1; print (y); } Which of the following statement(s) is/are correct ?
Worm threads are deeper than ACME threads.
In context of Java Threads, which of the following statements are true? I: sleep () and yield () are static methods in thread class II: yield () voluntarily relinquishes CPU to other threads. III: Daemon will terminate when all non-Daemon threads terminate.
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
Steps are given to draw involute of given circle. Arrange the steps f C is the centre of circle and P be the end of the thread (starting point). i. Draw a line PQ, tangent to the circle and equal to the circumference of the circle. ii. Draw the involute through the points P1, P2, P3 ……..etc. iii. Divide PQ and the circle into 12 equal parts. iv. Draw tangents at points 1, 2, 3 etc. and mark on them points P1, P2, P3 etc. such that 1P1 =P1l, 2P2 = P2l, 3P3= P3l etc.
The diameter of knuckle pin in a knuckle joint is usually taken as (where d = Diameter of the rod)
Which of the following are components of the knuckle joint assembly?  I) Knuckle pin II) Single eye III) Double-eye
If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.