Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s2, then find the correction couple in N-m.
If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?
Which of the following are components of the knuckle joint assembly?  I) Knuckle pin II) Single eye III) Double-eye
For a steam engine, the following data is given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m calculate inertia force at θ=30 degrees from IDC.
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.
From the data given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the correcting couple in N-m?
The figure shows a 5 cm diameter rod, 90 cm long, which is having its lower face grinded smooth. The remainder of the rod is exposed to 32 degree Celsius room air and a surface coefficient heat transfer equal to 6.8 W/m2 degree exists between the rod surface and the room air. The grinder dissipates mechanical energy at the rate of 35 W. If thermal conductivity of rod material is 41.5 W/m degree, find the temperature of the rod at the point where the grinding is taking place