Given: Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the addendum height for the smaller gear wheel in mm.

Given: Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the addendum height for the smaller gear wheel in mm. Correct Answer 6.2

r = m.t/2 = 100mm R = 200mm Using the constraint we find that ra = 106.2mm Therefore Addendum height = 6.2mm.
Bissoy MCQ

Related Questions

Given, Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the addendum height for the larger gear wheel in mm.
Given: Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the length of path of contact in mm.
Given: Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the length of arc of contact in mm.
Given: Involute profile teeths of mating gear: 20 and 40 Pressure angle = 20° module = 10mm The constraint: The addendum on each wheel is to be made of such a length that the line of contact on each side of the pitch point has half the maximum possible length. Find the contact ratio.
Which of the following statements are correct for mating gears with involute profiles? (i) The pressure angle, from the start of the engagement to the end of the engagement, remains constant. (ii) The pressure angle is maximum at the beginning of the engagement, reduces to zero at pitch point, starts decreasing and again becomes maximum at the end of the engagement. (iii) The face and flank of the teeth are generated by a single curve and the normal to this curve at any point is tangent to the base circle of the gear. (iv) The centre distance for a pair of mating gears can be varied within limits without altering the velocity ratio. Select the correct answer using the code given below.
Find maximum sliding velocity in cm/s from the given data addendum = 1 module = 5mm Pitch line speed = 1.2m/s Pressure angle of involute profile: 20 degrees Tp = 20 Gear ratio = 2
Two involute gears in a mesh have a module of 10 mm and the pressure angle is 35°. The larger gear has 45 teeth whereas the pinion has 15 teeth. The addendum is equal to one module. Find the arc of contact.
Two involute gears have a pressure angle of 20°. The gear ratio is given to be 3. The module is 5 mm and the value of addendum is equal to 1 module. Determine the minimum number of teeth on each wheel to avoid interference, if the pinion rotates at 100 rpm.
When the addenda on pinion and wheel is such that the path of approach and path of recess are half of their maximum possible values, then the length of the path of contact is given by (where r = Pitch circle radius of pinion, R = Pitch circle radius of wheel and $$\varphi $$ = Pressure angle)
Find the maximum value of addendum radius of the larger gear if the pressure angle between two teeth is equal to 25°. T = 50 and t = 25. The gears have a module of 8 mm and the addendum is equal to one module.