Bissoy.com
Doctors Medicines MCQs Q&A

For the same crank length and uniform angular velocity of the crank in an offset slider crank mechanism, if the connecting rod length is increased by 1.5 times, the velocity of piston will

For the same crank length and uniform angular velocity of the crank in an offset slider crank mechanism, if the connecting rod length is increased by 1.5 times, the velocity of piston will Correct Answer decrease by 1.5 times

V1 = ωr(sinϴ + sin2ϴ/2n) V2 = ωr(sinϴ + sin2ϴ/3n) from these two equation, V2 1 V2 will decrease but correct quantification can not be done with available data. Among the available options, best answer is (c).

Related Questions

Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
In a slider crank mechanism, the crank rotates with a constant angular velocity of 300 rpm, Length of crank is 150mm, and the length of the connecting rod is 600mm. Determine linear velocity of the midpoint of the connecting rod in m/s. Crank angle = 45° from IDC.
In a slider crank mechanism, the crank rotates with a constant angular velocity of 300 rpm, Length of crank is 150mm, and the length of the connecting rod is 600mm. Determine acceleration of the midpoint of the connecting rod in m/s2. Crank angle = 45° from IDC.
In a slider crank mechanism, the length of the crank and connecting rod are 180 mm and 540 mm respectively. The crank position is 45° from inner dead centre. The crank shaft speed is 450 r.p.m. (clockwise), calculate angular velocity of the connecting rod in rad/s.
Consider the following statements: In a slider-crank mechanism, the slider is at its dead centre position when the (i) slider velocity is zero (ii) slider velocity is maximum (iii) slider acceleration is zero (iv) slider acceleration is maximum Which of the above statements are correct?
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the equivalent length L of a simple pendulum swung about an axis.
A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
For a steam engine, the following data is given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m calculate inertia force at θ=30 degrees from IDC.
From the data given: Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m ; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find the correcting couple in N-m?
In the below figure, PC is the connecting rod and OC is the crank making an angle $$\theta $$ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, the acceleration of the piston is _________ when the crank OC and connecting rod PC are at right angles to each other.