Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

The lengths of the links of a 4- bar linkage with revolute pairs only are p,q,r and s units. Given that p < q < r < s and s+p < q+r which of these links should be the fixed one, for obtaining a ‘double crank’ mechanism?
The figure shows a mechanism with 3 revolute pairs (between the links 1 and 2, 2 and 3, and 3 and 4) and a prismatic pair (between the links 1 and 4). Which one of the four links should be fixed to obtain the mechanism that forms the basis of the quick-return mechanism widely used in a shaper?
Match list I with list II List I List II A. Pantograph 1. Scotch yoke mechanism B. Single slider crank 2. Double lever mechanism C. Double slider crank chain 3. Tchebicheff’s mechanism D. Straight line motion mechanism 4. Double crank 5. Hand pump
A planar four-bar linkage mechanism with 3 revolute kinematic pairs and 1 prismatic kinematic pair is shown in the figure, where AB ⊥ CE and FD ⊥ CE. The T-shaped link CDEF is constructed such that the slider B can cross the point D, and CE is sufficiently long. For the given lengths as shown, the mechanism is
An operating system uses the Banker’s algorithm for deadlock avoidance when managing the allocation of three resource types X, Y, and Z to three processes P0, P1, and P2. The table given below presents the current system state. Here, the Allocation matrix shows the current number of resources of each type allocated to each process and the Max matrix shows the maximum number of resources of each type required by each process during its execution.   Allocation Max   X Y Z X Y Z P0 0 0 1 8 4 3 P1 3 2 0 6 2 0 P2 2 1 1 3 3 3   There are 3 units of type X, 2 units of type Y and 2 units of type Z still available. The system is currently in a safe state. Consider the following independent requests for additional resources in the current state: REQ1: P0 requests 0 units of X, 0 units of Y and 2 units of Z REQ2: P1 requests 2 units of X, 0 units of Y and 0 units of Z Which one of the following is TRUE?
A 4-bar mechanism with all revolute pairs has link lengths lf = 20 mm, lin = 40 mm, lco = 50 mm and lout = 60 mm. The suffixes 'f', 'in', 'co' and 'out' denote the fixed link, the input link, the coupler and output link respectively. Which one of the following statements is true about the input and output links?
The rate of electricity in the rural area is given below: i) up to 25 units - Rs 5 per unit ii) up to 75 units - Rs 7 per units iii) up to 100 units - Rs 9 per units iv) After 100 units - Rs 13 per units Additional charge after 100 units = Rs. 50 The consumption of the electricity of the household is 120 units. How much electricity bill he has to pay?
Statement I: In four-bar chain, whenever all four links are used, with each of them forming a turning pair, there will be continuous relative motion between the two links of different lengths. Statement II: For a four-bar mechanism, the sum of the shortest and longest link lengths is not greater than the sum of remaining two links.
Raw material purchased:
1st January, 600 units @ Rs. 12 per unit
12th January, 500 units @ Rs. 14 per unit
21st January, 300 units @ Rs. 13 per unit
Raw material issued for manufacture:
3rd January 300 units
5th January 124 units
15th January 250 units
16th January 300 units
Raw material returned to stores from manufacturing department on 14th January, 50 units. The material is issued on First-in-First out method.
The value of material remaining in store on 21st January will be:
In a slider crank mechanism, the length of the crank and connecting rod are 150 mm and 600 mm respectively. The crank position is 60° from inner dead centre. The crank shaft speed is 400 r.p.m. (clockwise). Velocity of the slider is ________