Related Questions

A plate with an elliptical hole in the centre, with semi-major axis (a) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where $$\sigma $$ = Stress for a plate with no hole i.e. nominal stress)
A $$\sigma \left( {1 + \frac{{\text{b}}}{{2{\text{a}}}}} \right)$$
B $$\sigma \left( {1 + \frac{{2{\text{a}}}}{{\text{b}}}} \right)$$
C $$\sigma \left( {1 + \frac{{\text{b}}}{{3{\text{a}}}}} \right)$$
D $$\sigma \left( {1 + \frac{{3{\text{a}}}}{{\text{b}}}} \right)$$
The stress induced in a body, when suddenly loaded, is _________ the stress induced when the same load is applied gradually.
A Equal to
B One-half
C Twice
D Four times
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
The stress induced in a body will be shear stress, when it is subjected to
A Longitudinal vibrations
B Transverse vibrations
C Torsional vibrations
D None of these
When a body is subjected to two equal and opposite pulls, as a result of which the body tends to extend its length, the stress and strain induced is
A Compressive stress, tensile strain
B Tensile stress, compressive strain
C Tensile stress, tensile strain
D Compressive stress, compressive strain
When a body is subjected to two equal and opposite forces, acting tangentially across the resisting section, as a result of which the body tends to shear off across the section, the stress and strain induced is
A Tensile stress, tensile strain
B Compressive stress, compressive strain
C Shear stress, tensile strain
D Shear stress, shear strain
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A $$\frac{{{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
B $$\frac{{2{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
C $$\frac{{4{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
D $$\frac{{8{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
The maximum stress due to stress concentration in a bar having circular transverse hole, as compared to its static stress without hole will be
A Same in both cases
B 2 times more
C 3 times more
D 4 times more
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
When a body is subjected to a direct tensile stress ($${\sigma _{\text{x}}}$$) in one plane accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), the maximum shear stress is
A $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{{{\sigma _{\text{x}}}}}{2} - \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
C $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 - 4\tau _{{\text{xy}}}^2} $$
D $$\frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$

Next steps