Bissoy.com
Doctors Medicines MCQs Q&A

A plate condenser was designed to be kept vertical. How would the condensation coefficient be effected if due to site constraints, it has to be kept at 60 degree to the horizontal?

A plate condenser was designed to be kept vertical. How would the condensation coefficient be effected if due to site constraints, it has to be kept at 60 degree to the horizontal? Correct Answer 3.53% reduction in condensation coefficient

h VER = 0.943 0.25, h INC = 0.943 0.25.

Related Questions

Let D be a simple graph on 10 vertices such that there is a vertex of degree 1, a vertex of degree 2, a vertex of degree 3, a vertex of degree 4, a vertex of degree 5, a vertex of degree 6, a vertex of degree 7, a vertex of degree 8 and a vertex of degree 9. What can be the degree of the last vertex?
A hot plate of 15 cm2 area maintained at 200 degree celsius is exposed to still air at 30 degree Celsius temperature. When the smaller side of the plate is held vertical, convective heat transfer rate is 15 per cent higher than bigger side of the plate is held vertical. Find size of the plate. The appropriate correlation for the convection coefficient is Nu = 0.60 (Gr Pr) 0.25
A two pass surface condenser is required to handle the exhaust from a turbine developing 15 MW with specific steam consumption of 5 kg/k W h. The quality of exhaust steam is 0.9, the condenser vacuum is 66 cm of mercury while the bar meter reads 76 cm of mercury. The condenser tubes are 28 mm inside diameter, 4 mm thick and water flows through tubes with a speed of 3 m/s and inlet temperature 20 degree Celsius. All the steam is condensed, the condensate is saturated water and temperature of cooling water at exit is 5 degree Celsius less than the condensate temperature. Assuming that overall coefficient of heat transfer is 4 k W/m2 degree, determine the mass of cooling water circulated
A plate condenser of dimensions l * b has been designed to be kept with side l in the vertical position. However due to oversight during erection and installation, it was fixed with side b vertical. How would this affect the heat transfer? Assume laminar conditions and same thermos-physical properties and take b = l/2
The rear window of an automobile is made of thick glass i.e. AB = 5 mm and thermal conductivity is 0.8 W/m degree. To defrost this window, a thin transparent film type heating element has been fixed to its inner surface. For the conditions given below, determine the electric power that must be provided per unit area of window if a temperature 5 degree Celsius is maintained at its outer surface. Interior air temperature and the corresponding surface coefficient are 20 degree Celsius and 12 W/m2 degree. Surrounding air temperature and the corresponding surface coefficient are – 15 degree Celsius and 70 W/m2 degree. Electric heater provides uniform heat flux
Study the following statements.i) The displacement method is more useful when degree of kinematic indeterminacy is greater than the degree of static indeterminacy.ii) The displacement method is more useful when degree of kinematic indeterminacy is less than the degree of static indeterminacy.iii) The force method is more useful when degree of static indeterminacy is greater than the degree of kinematic indeterminacy.iv) The force method is more useful when degree of static indeterminacy is less than the degree of kinematic indeterminacy.The correct answer is
A steam condenser is transferring 250 k W of thermal energy at a condensing temperature of 65 degree Celsius. The cooling water enters the condenser at 20 degree Celsius with a flow rate of 7500 kg/hr. If overall heat transfer coefficient for the condenser surface is 1250 W/m2 K, what surface area is required to handle this load?
Rinki has three plates of Jalebies: Plate A, Plate B and Plate C. Plate A has only one Jalebi, Plate B has five Jalebies and Plate C has three Jalebies. She wants to put equal numbers of Jalebies in all the plates. Which of the following statement is true?
A nuclear reactor with its core constructed of parallel vertical plates 2.25 m high and 1.5 m wide has been designed on free convection heating of liquid bismuth. Metallurgical considerations limit the maximum surface temperature of the plate to 975 degree Celsius and the lowest allowable temperature of bismuth is 325 degree Celsius. Estimate the maximum possible heat dissipation from both sides of each plate. The appropriate correlation for the convection coefficient is Nu = 0.13 (Gr Pr) 1/3
A water line is buried underground in dry soil that has an assumed initial temperature of 4.5 degree Celsius. The pipe may have no flow through it for long period of time, yet it will not be drained in order that no freezing occurs, the pipe must be kept at a temperature not lower than 0 degree Celsius. The pipe is to be designed for a 30 hour period at the beginning of which the soil surface temperature suddenly drops to – 17 degree Celsius. Workout the minimum earth covering needed above the water pipe so as to prevent the possibility of freezing during 36 hour cold spell. The soil in which the pipe is buried has the following properties Density = 640 kg/m3 Specific heat = 1843J/kg degree Thermal conductivity = 0.345 W/m degree