Bissoy.com
Doctors Medicines MCQs Q&A

At the beginning of the compression stroke, intake valve opens and the air fuel mixture is sucked into the cylinder during the suction stroke.

At the beginning of the compression stroke, intake valve opens and the air fuel mixture is sucked into the cylinder during the suction stroke. Correct Answer False

No, but at the beginning of the suction stroke, intake valve opens and the air fuel mixture is sucked into the cylinder during the suction stroke.

Related Questions

The air or air-fuel mixture is ____ into cylinder through intake valve and ____ out of cylinder through exhaust valve.
“What is the different between height and radius of solid cylinder?” Which of the following option is sufficient alone to find the answer? A) A solid cylinder is made by melting a solid sphere. The radius of cylinder is 3 times the radius of a circle whose area is 154 sq.m. Height of cylinder is equal to the height of cone whose volume is 2772 cubic meters. B) Area of a rectangle whose longer side is ¾ times the radius of a solid cylinder, is 168 sq.m and, Volume of solid cylinder is 2772 cubic meters and its height is 18 m. C) A metallic cone of radius 15m and height 35m is melted into the solid cylinder of radius equal to the radius of a circle whose area is equal to the area of rectangle whose sides are in the ratio 4 : 3 respectively. D) The curved surface area of the solid cylinder is 3 time the surface area of a sphere of radius 7m and height of cylinder is equal to the height of a metallic cone whose curved surface area is 308 sq.m. 
In MPFI-Air Induction System, the air cleaner, the air flow meter, the throttle body and the air valve supply a proper amount of air to the air intake chamber and intake manifold.
In IC engine 1. the ideal air capacity of a two-stroke engine is the mass of air required to concurrently fill the total cylinder volume at inlet temperature and exhaust pressure 2. with increase in air-fuel ratio beyond the value for maximum power, there is a fall in power developed and this fall is more with higher values of air-fuel ratio. 3. the volumetric efficiency of the engine depends on the design of intake and exhaust manifold. Which of the above are correct?
The pipe which connects the intake system to the inlet valve of the engine and through which air or air-fuel mixture is drawn into the cylinder is known as _______
The volume of air sucked by the compressor during its suction stroke is called
In the four cylinder engine, the ECU calculates the appropriate injection timing for each cylinder and the air fuel mixture is made available at each suction stroke.
A solid-oxide fuel cell is fed with carbon monoxide and reacts with air to produce CO2. This reaction will produce 2 electrons which are used to power an electric circuit external to the fuel cell. The reaction equation is shown below: 2CO(g) + O2(g) -> 2CO2(g) ΔHr° = -565.96 kJ/mol This reaction does not occur for other types of fuel cells which use a catalyst, such as polymerelectrolyte membrane or phosphoric-acid fuel cells. The presence of carbon monoxide on the anode side of these types of fuel cells will cause catalyst poisoning, reducing the efficiency and voltage of the fuel cell. Determine the rate of enthalpy change for a carbon dioxide production rate of 208 mol/hr. The extent of the reaction occurring in the fuel cell can be obtained by the following equation: where:
oil and kerosene are present in ratio of 5 : 7 in a liquid. Few litres of mixture of mixture are replaced with petrol. Ratio of oil : kerosene: petrol is 35 : 49 : 18 respectively. Amount of oil removed from mixture is 21 litres less than that of petrol added to the mixture. And amount of oil removed is 6 litres less than that of difference mentioned. Petrol is replacing the mixture removed hence; quantity of mixture is not changing. What is the difference between quantity of kerosene in old mixture and amount of oil in new mixture?
If p₁, is the pressure of air entering the L.P. cylinder and p₂ is the pressure of air leaving the L.P. cylinder (or inter-cooler pressure), then the ratio of cylinder diameters for a single acting, two stage reciprocating air compressor with complete intercooling is given by (where D₁ = Dia. of L.P. cylinder, and D₂ = Dia. of H.P. cylinder)