Bissoy.com
Doctors Medicines MCQs Q&A

A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring.

A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. Correct Answer 1800N

mv²/2=Pxdeflection/2.

Related Questions

A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm, find the speed of the turntable in rpm if ratio of the governor speed to the turntable speed is 10.5.
A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs.
A closely coiled helical spring is acted upon by an axial force. The maximum shear stress developed in the spring is $$\tau $$. The half of the length of the spring if cut off and the remaining spring is acted upon by the same axial force. The maximum shear stress in the spring in new condition will be
A block of mass M is attached to the lower end of a vertical spring. The spring is hung from a ceiling and has a force constant value k. The mass is released from rest with the spring initially unstretched. The maximum extension produced in the length of the spring will be:
Given data for bracket is P=20kN, e=100mm, S(yt)=400N/mm², FS=3. If distance between the bolts from the axis of tilting is 125mm and 25mm, then find the effective tensile force acting on the bolts lying at 125mm from tilting axis.
Two horse drawn wagons start from the same farm. Wagon X travels South for 4.5 km and then turns right and travels for 7.5 km. In the meanwhile, wagon Y travels 9 km North, then 3.5 km West, then 2 km North, then it turns left and travels 4 km. Where is wagon Y with respect to wagon X?
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
A spring mass system is on a horizontal plane. Spring constant is 2N/m & mass of block is 2kg. The spring is compressed by 10cm and released. A small ball is released from a height of 2m above the block on the horizontal plane. At what time should the ball be left if the block is released from the extreme position at t=0, given that the ball has to fall on the block when the speed of block is maximum?
A Pickering governor is driving a gramophone. Each disc attached to the centre of a leaf spring has a mass of 20 g. The width of each spring is 5 mm and thickness of 0.125 mm. The effective length of each spring is 40 mm. The distance from the spindle axis to the centre of gravity of the mass when the governor is at rest, is 10 mm. Find the speed of the governor in rpm when the sleeve has risen to a height of 0.8 mm. (E = 210kN/mm2)
A centrifugal clutch has four shoes. When the clutch is at rest, each shoe is pulled against a stop by a spring so that it leaves a radial clearance of 7.5 mm between the shoe and the rim. The pull exerted by the spring is then 600 N. The mass centre of the shoe is 120 mm from the axis of the clutch. If the internal diameter of the rim is 350 mm, the mass of each shoe is 5 kg, the stiffness of each spring is 60 N/mm and the coefficient of friction between the shoe and the rim is 0.2; find the speed of the centrifugal clutch, if the power transmitted is 40.168 kW.