Bissoy.com
Doctors Medicines MCQs Q&A

Vibratory feeder or toothed belt feeder as used to measure the quantity of the abrasive particles before mixing.

Vibratory feeder or toothed belt feeder as used to measure the quantity of the abrasive particles before mixing. Correct Answer True

Metered abrasive particles are introduced into the mixing chamber through a port. The abrasive particles are metered using different techniques like a vibratory feeder or toothed belt feeder. The reader may consult standard literature on transportation of powders.

Related Questions

Consider the following statements regarding vibratory rollers: (i) Vibratory rollers are used for compacting granular soils and pavement layers with granular materials. (ii) Vibratory rollers are used for compacting non-plastic silts and fine sands. (iii) In vibratory rollers, compaction is effected due to both the dynamic effect of the vibratory force and also the static weight of the roller. Which of the above statement(s) is/are correct?
Consider the following statements regarding V-belt drive : 1. The groove angle of the sleeve is less than the belt section angle 2. The efficiency of a V-belt drive is higher than that of a flat belt drive 3. The groove angle is so made that the belt gets wedged in the groove  Which of the above statements are correct ? 
Given below are two quantities named A and B. Based on the given information, you have to determine the relation between the two quantities. You should use the given data and knowledge of Mathematics to choose between the possible answers. There are two jars which contain different liquids in different quantities Quantity I∶ Quantity of water in Jar 1, if Jar 1 contains mixture of 230 litres which contain juice, water, coke and pepsi. Ratio of quantity of water to juice is 2 : 1 and juice to coke is also 2 ∶ 1 while the ratio of quantity of coke to pepsi is 3 ∶ 2 Quantity II∶ Quantity of water in Jar 2, if Jar 2 contains 10 litres of mixture more than jar 1 and contains juice, coke and water. Water, juice and coke is poured into the jar 8 times in the ratio 3 ∶ 2 ∶ 1. Every time the quantity of a liquid is same.
Consider the following statements in respect of ‘mixers’ 1. Mass batch mixing of ingredients is the most desirable method. 2. Charging all materials into a drum mixer is done ‘at once’. 3. The quantity of material fed into a mixer should be not more than the quantity that can be used in less than 30 minutes after completion of mixing. 4. Reversing mixers have less capacity than tilting mixers. 5. In large mixers, additional time of mixing is allowed. Which of the above statements are correct?
When the belt is transmitting maximum power, the belt speed should be (Where, m = mass of belt per meter (kg/m) and Pmax = maximum permissible tension in belt (N))
The efficiency of flat belt drive is 35%. If all the parameters are same and flat belt is replaced by V belt, than the efficiency of V belt will be?
When the belt is transmitting maximum power, the belt speed should be
(Where, m = mass of belt per meter (kg/m) and Pmax = maximum permissible tension in belt (N))
A bucket wheel excavator with 20 buckets of capacity 0.5 m3 each, rotates at 5 rev/min. The bucket fill factor is 80%. The excavator loads on to 1200 mm wide belt conveyor. The cross-section area (m2) of the material on the belt is 0.1B2, where B is the belt width in m. The minimum speed of the belt in m/s to avoid spillage of material is
The ratio of belt tensions $$\frac{{{{\text{p}}_1}}}{{{{\text{p}}_2}}}$$ considering centrifugal force in flat belt is given by where,
m = mass of belt per meter (kg/m)
v = belt velocity (m/s)
f = coefficient of friction
$$\alpha $$ = angle of wrap (radians)
Which of the following belts are associated with seismic activity?
1. Circum-Pacific Belt
2. Circum-Atlantic Belt
3. Mid-Continental Belt
4. Mid-Atlantic Belt