Bissoy.com
Doctors Medicines MCQs Q&A

Nominal bearing strength of bolt is 2.5kbdtfu where kb depends on (i) end distance, (ii)pitch distance, (iii)ultimate tensile stress of bolt, (iv)shank area of bolt, (v)yield stress of bolt, (vi)diameter of hole

Nominal bearing strength of bolt is 2.5kbdtfu where kb depends on (i) end distance, (ii)pitch distance, (iii)ultimate tensile stress of bolt, (iv)shank area of bolt, (v)yield stress of bolt, (vi)diameter of hole Correct Answer i, ii, iii, vi

Nominal bearing strength of bolt is 2.5kbdtfu, where kb is smaller of e/3d0, p/3d0 -0.25, fub/fu, 1 ; where e, d = end and pitch distances, d0= diameter of hole, fub and fu = ultimate tensile stress of bolts and plate, d = nominal diameter of bolt.

Related Questions

A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)
Which of the following stresses are associated with the tightening of a nut on a bolt? P. Tensile stress due to the streching of bolt Q. Bending stress due to the bending of bolt R. Torsional shear stress due to frictional resistance between the nut and the bolt Select the correct answer using the codes given below.
Calculate ultimate moment and shear of effective span is 30m, live load is 9kn/m, dead load excluding self weight is 2kn/m, load factors for dead load is 1.4 for live load is 1.6 cube strength of concrete fcu is 50n/mm2 cube strength at transfer is fci is 35n/mm2, tensile strength of concrete Ec is 34kn/mm2 loss ratio ɳ is 0.85 and 8mm diameter high tensile strength fpu is 1500n/mm2 are available for use and the modulus of elasticity of high tensile wires is 200kn/mm2?
A plate with an elliptical hole in the centre, with semi-major axis (a) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where $$\sigma $$ = Stress for a plate with no hole i.e. nominal stress)
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the effective tensile force acting in the two bolts.
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the ratio of the effective tensile load to which the two bolts are subjected.
An angle ISA 50 × 50 × 6 is connected to a gusset plate 5 mm thick, with 16 mm bolts. What is the bearing strength of the bolt when the hole diameter is 16 mm and the allowable bearing stress is 250 MPa?
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Which bolt is used a criterion for designing?
Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength
Compared to mild steel, cast iron has
(i) High compressive strength
(ii) High tensile strength
(iii) Low compressive strength
(iv) Low tensile strength