Bissoy.com
Doctors Medicines MCQs Q&A

The change in slope between any two points on the elastic curve equals the area of M/EI diagram between both end points of beam. State whether the above statement is true or false.

The change in slope between any two points on the elastic curve equals the area of M/EI diagram between both end points of beam. State whether the above statement is true or false. Correct Answer False

Change in slope will be equal to area of M/EI diagram between those two points.

Related Questions

Consider the following statements regarding types of supports and beams: 1. When both supports of beams are roller supports, the beam is known as simply supported beam. 2. A beam with one end fixed and the other end free is known as fixed beam. 3. A beam with both ends fixed is known as cantilever beam. 4. A beam with one end fixed and the other simply supported is known as propped cantilever. Which of the above statements is/are correct ?
Consider the following statements with regards to the shear force diagram for the beam ABCD: 1. The beam ABCD is an overhanging beam having supports at A and D only. 2. The beam carries a point load of 20 kN at C. 3. The beam carries a concentrated load of 10 kN at the end B. 4. The beam is an overhanging beam having supports at C and D only. 5. The beam carries a uniformly distributed load of 70 kN over the left hand portion AC only. Which of the above statements are correct?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
Determine the corrections or otherwise of the following Assertion and Reason : Assertion : For longitudinal static stability of an aircraft, slope of moment curve should be negative. Reason: Positive slope will result in more static stability than negative slope. Hence, slope should be positive always. and are true and is the correct reason for b) Both and are true but is not the correct reason for c) is true but is false d) is false but is true
In which of the following cases, there exists the situation of Pure Bending in some part of the beam or along the entire beam? i) A simply supported beam subjected to two equally spaced downward concentrated loads ii) A simply supported beam subjected to two equally spaced opposite moments iii) A cantilever beam subjected to clockwise moment at free end iv) An overhanging beam with both side overhangs subjected to different concentrated loads at both the free ends
Elastic-Beam theory can be applied on a non-linear elastic material. State whether the above statement is true or false.
Two processes X and Y need to access a critical section. Consider the following synchronization construct used by both the processes Process ? /* other code for process ? */ while(true) { varP = true; while(varQ == true) { /* Critical Section */ varP = false; } } /* other code for process ?? */   Process ? /* other code for process ? */ while(true) { varQ = true; while(varP == true) { /* Critical Section */ varQ = false; } } /* other code for process ? */   Here, varP and varQ are shared variables and both are initialized to false. Which one of the following statements is true?
Elastic failure of a material occurs, when the tensile stress equals yield strength, yield point or the elastic limit. Also, the elastic failure occurs according to maximum strain theory, when the maximum tensile strain equals (where, σ = yield strength and E = modulus of elasticity)
Elastic failure of a material occurs, when the tensile stress equals yield strength, yield point or the elastic limit. Also, the elastic failure occurs according to maximum strain theory, when the maximum tensile strain equals (where, $$\sigma $$ = yield strength and E = modulus of elasticity)
Consider the following with reference to Article 18? (a) No title, not being a military or academic distinction, shall be conferred by the State. (b) The citizen of India shall accept any title from any foreign State. (c) No person who is not a citizen of India shall, while he holds any office of profit or trust under the State, accept without the consent of the President any title from any foreign State. (d) The person holding any office of profit or trust under the State shall, without the consent of the President, accept any present, emolument, or office of any kind from or under any foreign State.